User manual SAMSUNG SC-8345

[. . . ] Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. x Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. x Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. [. . . ] Result: x Each time you press the button: - The temperature is adjusted by 1C - The indoor unit beeps E-9 Cooling Your Room You must select the Cool mode if you wish to adjust the: Cooling temperature Fan speed when cooling 1 If necessary, press the Result: button. The operation indicator on the indoor unit lights up. The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, button on the remote control one or more times until it press the appears. Result: The indoor unit beeps each time you press the The air conditioner runs in the Cool mode. button. Note 3 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 16C and 30C inclusive. Result: Each time you press the button: - The temperature is adjusted by 1C - The indoor unit beeps The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature. If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. button one or more times ) 4 Select the fan speed by pressing the until the required setting is displayed: Automatic (rotated : Low Medium High Maximum Result: Each time you press the beeps. button, the indoor unit 5 To control the direction of the air flow, refer to page 15. E-10 Removing Excess Humidity ENGLISH If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 If necessary, press the Result: button. x The operation indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. x Blinking of the timer indicator stops. x The selected mode and the temperature on the display disappear after 10 seconds. x The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On Timer setting. 3 To select an operating mode in advance, press the button until the desired mode is displayed at the top of the remote control. Result: The air conditioner will run in the selected mode when it is turned on. Note If you don't operate the remote control after setting the On Timer, it will be turned off automatically after 25 hours. To Cancel the On Timer If you no longer wish to use the On Timer that you have set, you can cancel it at any time. If you want to turn on the air conditioner before the timer reaches the setting time, press the button. E-16 Setting the Off Timer ENGLISH The Off Timer enables you to switch off the air conditioner automatically after a given period of time. You can set the period of time from 1 hour to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 1 hour and 24 hours inclusive. 2 Press the Result: button to complete the setting. x Blinking of the timer indicator stops. x The air conditioner will switch off automatically when the counter displayed on the remote control reaches the set time and disappears the Off Timer setting. Example If you would like to turn the air conditioner on after 2 hours and to operate it for 2 hours: 1. Press the Note button until `2 Hr' is displayed. [. . . ] Note Even if the air conditioner has been switched on via the On/Off switch, operations can still be controlled using the remote control as usual. E-21 Solving Common Problems Before contacting the after-sales service, perform the following simple checks. They may save you the time and expense of an unnecessary call. Problem The air conditioner does not operate at all Explanation/Solution x Check that the breaker used for the air conditioner is switched on. x Check that the operation indicator on the indoor unit is on; if necessary press the button on the remote control. [. . . ]