User manual SANUS VISIONMOUNT DUAL-SIDED CEILING MOUNT-LC2A

[. . . ] LC2A Thank you for choosing the Sanus Systems VisionMountTM LC2A. The VisionMountTM LC2A is designed to mount two flat panel televisions up to 1270 mm (50 in) and weighing up to 59 kg (130 lb) each to an existing NPT 1-1/2 threaded pipe drop. The LC2A tilts the televisions from +5° to -15°, swivel up to ±90°, and roll ±6°. [. . . ] Replacement parts for products purchased through authorized dealers are shipped directly to you. [01] X 1 [02] X 1 [03] X 2 [04] X 4 [05] X 8 [06] X 4 Sanus Systems 2221 Hwy 36 West, St Paul, MN 55113 USA · 01. 04. 07 (6901-100129<00>) USA Customer Service 800. 359. 5520 · www. sanus. com 1/4-20 x 2. 0 in. [07] X 8 [08] X 8 1/4-20 [09] X 2 [10] X 2 [11] X 10 [12] X 1 [13] X 1 [14] X 1 [15] X 8 [16] X 8 [17] X 8 [18] X 8 M4 x 30mm M5 x 30mm M6 x 35mm M8 x 40mm [19] X 8 [20] X 8 [21] X 8 [22] X 8 [23] X 8 [24] X 8 [25] X 8 [26] X 8 [27] X 16 [28] X 8 [29] X 8 [30] X 8 2 6901-100129<00> 1 1 -1: TV with flat back 1 - 2: TV with curved back or obstruction 1-1 [27] [27] [23] [24] [15] [16] 1-2 [29] [27] [27] [23] [19] [29] [27] [27] [24] [20] M5 x 30mm M4 x 30mm [28] [25] [17] [30] [--] [28] [25] [21] M6 x 35mm [28] [26] [18] [30] [--] [28] [26] [22] M8 x 40mm [06] [06] 8x 6901-100129<00> 3 2 Do not overtighten the Nut [08]. The vise Assembly [05] must rotate freely around the Carriage Bolt [07]. [05] [07] 8x [08] [06] 1/4-20 x 2. 0 in. 3 3 -1 [04] [06] [04] [05] 4 6901-100129<00> CAUTION: To prevent property damage and/or personal injury, the CrossTubes [04] must extend beyond the outside edges of both Monitor Brackets [06]. Orient the Vise Assemblies [05] and [A] on both the Axis Assembly [03] and the second Monitor Bracket [06] so that the Cross Tubes [04] pass between the jaws. Do not over-tighten the four Vise Assemblies [05] and the two Vise Assemblies [A] . Turn the Allen Bolt until resistance is felt; then, tighten the Allen Bolt approximately 1 -1/2 turns or until the head of the Allen Bolt is slightly above the surface of the Vise Assembly. The Cross Tubes [04] will not be able to move side-to-side when the Vise Assembly is properly tightened. Tighten all six Allen Bolts on both TVs 3-2 [A] [06] [04] [03] [14] [05] [A] 4 [01] [02] 6901-100129<00> 5 5 Thread the Coupler [01] and Tube [02] onto an existing threaded pipe drop. Once the Tube [02] is properly aligned, tighten the Set Screws [10] using Allen Wrench (12) and the two Set Screws [B] on the Tube using Allen Wrench (13). [12] [13] [10] [02] [B] [01] [02] [10] 6 6 -1 6-2 For clairity, TV is not shown. [09] [03] [02] [02] [03] 6 2x 6901-100129<00> 7 To adjust for level, loosen the two Allen Bolts [C] on the back of the Axis Assembly [03]. Adjust the television and retighten the Allen Bolts. Tilt is set by simply tilting the television. To adjust tilt tension, loosen the Tension Knobs [D]. 7 -1 [14] 2x [C] [D] [03] CAUTION Never completely remove the Tension Nut [E]. The Safety Bracket [F] must be reinstalled after adjustment. Hex hole in Safety Bracket must seat completely down onto Tension Nut [E]. [. . . ] The information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. 8 6901-100129<00> [. . . ]