User manual SANYO AVL-472

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION RISK OF ELECTRIC SHOCK CAUTION-To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www. eia. org FCC STATEMENT FCC Notice LCD TV: A CLASS B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] Press 5or6 to select Feature menu, press OK or4 to access the submenu. Press 5or6 to select Menu Language item, press OK or4 to select your desired language. Press EXIT button to return to TV viewing. Video Audio Source TV Time Set Sleep Timer Off Password Set Parental Control Closed Caption Options CC when Mute Off English Setup Menu Language Feature To Move OK To Select Exit To Exit Selecting Input Source Signal Navigate to the Feature menu and highlight Source. Press OK or4 to select your desired input source. Source Video TV Audio Time Set Sleep Timer Off Password Set Parental Control Closed Caption Options CC when Mute Menu Language Off English Setup Note: You may directly press INPUT button on the remote control to select input source. Feature To Move OK To Select Exit To Exit TV --------Select TV signal. Composite1-------Select signal from AV INPUT1 terminals. HDMI1-------Select signal from HDMI1 input interface. Composite2-------Select signal from AV INPUT2 terminals. HDMI2-------Select signal from HDMI2 input interface. Component1------Select signal from COMPONENT INPUT1 terminals. Component2------Select signal from COMPONENT INPUT2 terminals. S-Video-------Select signal from S-VIDEO input terminal. 14 Memorizing the Channels This unit can automatically find all channels available through antenna or cable inputs, and store them in memory. Selecting the Tuning Band Before your TV can memorize the available channels, you must specify the type of signal source that is connected to the unit. To quit, press EXIT button. Feature Channel Labels Menu Ch0005-0001 ------- To Move OK To Change Exit To Exit 16 Channel Selection Information about USA and Canadian channel numbering in the digital era = An ATSC channel has two part channel number: -- Major channel number -- Minor channel number For example: Channel: 5-1 Minor channel number Major channel number =In most situations the major channel number is same for both analog and digital channels (It is equal to the NTSC channel number for existing broadcasters. ) =A minor channel number of zero is used for a broadcaster's analog channel. Channel Numbering Example = Original NTSC Channels for Des Moines (via antenna): -- 5, 8, 11, 13, 17 = Possible NTSC + ATSC Channels for Des Moines (via antenna): -- 5-0, 8-0, 11-0, 13-0, 17-0 (channel numbers for existing analog channels) -- 5-1, 5-2, 8-1, 8-2, 8-3, 8-4, 13-1 (channel numbers for digital channels) In Canada, ATSC digital reception areas via antenna are limited. However digital coverage via cable or satellite is widespread (digital cable or satellite receiver required). Channel Selection Using the Channel up/down buttons (CH+ or CH-) Press the CH+ or CH- to cycle among available channels found. Using the direct select buttons (0-9 and dash buttons) Press the number buttons (0-9) and the dash button (-) to go directly to a channel. For example, if you want to select channel 8-3, just key in `8', `-', `3' on the remote control. Note: =When you use the number buttons, you can directly select any channel within the channel range . =To select an analog channel, you may directly input its major channel number. It is unnecessary to input the =In some situations virtual channel numbers have no correspondence to physical frequencies. minor channel number of zero. Using the button Press this button to switch between the current channel and the last viewed channel. 17 Screen Setup for HDMI, S-Video, regular audio/video inputs and analog TV Customizing the Picture Picture Mode Contrast 50 Brightness 50 Color Sharpness Aspect Ratio Advanced Video Menu To Move OK To Select Exit To Exit 50 0 Wide User 1 2 3 4 5 Press MENU to display the menu main page. Press 5or6 repeatedly to select Video menu. Press OK or4 to access the submenu. Video Audio Setup Feature Within the menu, use 5, 6, 3or4 to navigate or adjust. Press OK or 4button to confirm, enter sub-menu or toggle Notes: the settings of the selected menu item. The OSD illustration shown above is Video menu in RF(TV) mode. The menu items may be different when the unit works in different mode. Option Function Choice/remarks Note: you may directly press PICTURE button on the remote control to select. User/Nature/Soft/Bright 4: stronger 3: weaker 4: lighter 3: darker 4: stronger 3: weaker Picture Mode Contrast Brightness Selects a desired picture mode. Adjusts screen brightness for easier viewing of dark picture such as night scenes and black hair. [. . . ] Design and specifications are subject to change without notice. Weight and dimensions shown are approximate. Specifications and external appearance may be changed for the sake of improvement. 30 Note: The universal remote control unit can't be programmed to control a TV with other brand. It has been preset to control this TV set, and this preset is unchangeable. 31 32 33 34 35 36 37 38 39 40 SANYO COMFORT WARRANTY WARRANTY APPLICATION New, unused Sanyo Color Television products purchased in Canada through a Sanyo authorized dealer are warranted against manufacturing defects in materials and workmanship for ONE YEAR for parts and labor, from the date of purchase by the original retail purchaser for non-commercial use. [. . . ]