User manual SANYO DAS202 INSTRUCTION MANUAL

[. . . ] Fully Digital Answering System DAS 202 INSTRUCTION MANUAL Please read this operation manual before using your new answering machine and keep it for further reference 1 QUICK INSTRUCTIONS · Setting the Time ­ Press and hold `STOP/TIME' to enter the SET CLOCK mode ­ Press the FF c Key or the REPT d Key to adjust the day ­ Press `STOP/TIME' again to set the day ­ Repeat to set Hours and Minutes · Playing the Current Time ­ Press `STOP/TlME' · Recording the Outgoing Message (OGM) ­ Press and hold `OGM1' ­ Speak clearly into the microphone with your message ­ Press `STOP/TIME' to stop recording ­ Repeat the process for `OGM2' · Recording a Memo ­ Press and hold `MEMO/2WAY' for 2 seconds ­ Speak clearly into the microphone with your message ­ Press `STOP/TIME' to stop recording · 2 Way Recording ­ Press and hold `MEMO/2WAY' for 4 seconds ­ Have a normal conversation on your telephone ­ Press `STOP/TIME' to stop recording · Playing a Memo ­ Press `MEMO/2WAY' or `PLAY' · Setting to Answer/Record Mode or Answer Only Mode ­ If the system is in Answer Only Mode, press and hold `ANSWER' for about 2 seconds. ­ The DAS 202 will beep and OGM1 will play. ­ Repeat the process to return the system to ANSWER ONLY MODE. ­ The DAS 202 will beep and OGM2 will play · To turn on/off the answering system, press `ANSWER' · Playing Messages 1. [. . . ] If ER flashes once, this indicates that the DAS 202 needs to be reset. Please disconnect the unit from power, and then re-connect it. 8 Setting to Answer/Record Mode or Answer Only Mode ­ Note: When power is on, the system is always in either one of these 2 modes. · If the system is in Answer Only Mode, press `ANSWER' for about 2 seconds. The DAS 202 will beep and the LED will show `A1' while OGM1 playing. The DAS 202 is now in Answer/Record Mode. · Repeat the process to return the system to ANSWER ONLY MODE. The DAS 202 will beep and the LED will indicate `A2' while OGM2 playing. · The DAS 202 can be turned off or on by simply tapping the answer key. Recording Incoming Calls ­ When the DAS 202 is in Answer/Record mode, it will answer the telephone after the second (or fourth) ring*, then will play your OGM1 message. At the end of the OGM1 message a beep will sound, indicating to your caller that they may begin speaking. The DAS 202 allows callers to leave a message. At the end of the message, the DAS 202 will sound a long beep, indicating that the recording time is over. *Ring and Toll Saver ­ The DAS 202 will normally answer an incoming call after the second ring. However, if there are no unplayed messages on the system, the DAS 202 will not answer until after the fourth ring. This feature allows you to call into your answering machine and determine, without a toll, if there are any unplayed messages on the system (i. e. If the phone rings three times, there are no unplayed messages). Playing All Messages ­ The LED will display the total number of messages in the DAS 202's memory. The following details the playback procedures: · Playback Press `PLAY' · Pause Message Press `PLAY' · Resume Playback from Pause Press `PLAY' · Repeat Message Press `REPT d ' once to replay current message, twice to replay the previous message · Skip Message Press `FF c' once to skip the current message, multiple times to skip through more than one message · Erase Single Message Press `ERASE' while message is playing · Stop Playback Press `STOP/TIME' · Erase and Save ALL Messages Press and hold `ERASE' for about 2 seconds. A long beep will sound, and ALL messages will be erased. To RESTORE all messages, Press and hold `ERASE' again for about 2 seconds. A long beep will sound and messages will be restored. CAUTION: If you erase a single message during playback, it cannot be restored. 10 ADVANCED USE Playing your Outgoing Message (OGM) ­ To play your OGM, simply press the `OGM1' or `OGM2' button. [. . . ] Replacement PARTS are warranted for the remaining portion of the warranty period. WHAT IS NOT COVERED (a) Communications products purchased outside Canada. (b) Communications products purchased in a used condition. (c) Problems due to product set-up and installation. [. . . ]