User manual SANYO DCSC60

[. . . ] This manual explains the installation of the Network Board and its operation. Chapter 1 Preparation Chapter 2 Installation Chapter 3 Basic Setting & Operation Chapter 4 Controlling the Projector Chapter 5 Controlling the Multi-Projectors Chapter 6 Use of Serial Port Chapter 7 Appendix Compliance Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] AUTO . . . . . . . . . . . . . . . . It automatically switches to the scanning system of the input signal. These selections will not appear when the source mode is set to the computer mode. Network Board OWNER'S MANUAL 41 ENGLISH Chapter 4 Controlling the Projector Image Adjustment This function is to adjust the projected picture image and set the image mode. For selection of image mode, select a desired image mode with the Image Adjustment Mode pull-down menu button and then press the Set button. The setting items are switched automatically according to selected input mode, computer or video input. Item Description Image Adjustment*. Selects image mode among the Standard, Real, Cinema, Dynamic, Image1 to Image4 with pull-down button menu . Original Mode . . . . . . . . Displays which predefined image adjustment mode is based upon. Adjustment items . . . . . . . . . . . . . . . . . . Contrast, Brightness, Color, Tint BrilliantColor. . . . . . . . . . . . Improve the color performance with BrilliantColorTM technology. * Available image mode may differ from the actual depending on the projector's model type. Type1: Image1 to Image4 Type2: Image1 to Image10 Item Description White Balance Color Temp. Red, green, Blue . . . . . . . . . . . . . . . . Adjusts a white balance respectively. Item Description Sharpness. . . . . . . . . . Adjusts picture sharpness. Gamma . . . . . . . . . . . . . . Adjusts brightness of darker part of the picture. It moves quickly if the "High Speed" is checked. * The control button [Left], [Right] may be not available depending on the projector's model type. Item Description Background* . . . . . . Sets screen background when no input signal received Blue Back* . . . . . . . . Sets screen background color when no input signal received. Display . . . . . . . . . . . . . . Sets on-screen menu display Logo . . . . . . . . . . . . . . . . . . Sets the logo display setting on the screen during the startup. Ceiling. . . . . . . . . . . . . . . . Sets the image top/bottom and left/right reversed. Rear . . . . . . . . . . . . . . . . . . Sets the image left/right reversed. * Either of item "Blue Back" or "Background" may appear depending on the projector's model type. Item Description Shutter*1 . . . . . . . . . . . . Sets the image black out mode. No Show*1 . . . . . . . . . . Sets the image black out mode. Freeze. . . . . . . . . . . . . . . . Sets the image frozen mode. Power Management. . . . . . Sets the power management if the input signal is interrupted and no control key is pressed during the specified period of time. Sets the time periods*2 until the power management operates. On Start . . . . . . . . . . . . Sets the power-on mode when turning on the mains switch. [. . . ] Please see chapter "Controlling the Multi-Projectors" for further information ( p. 55). By registering the projector name and IP address with the DNS server, it can be accessed with the nickname from the any computer referred to the DNS server. Please consult your network administrator ( p. 31, 57). Chapter 7 Appendix Q Why am I not receiving E-mail alert messages?A Make sure that the registered E-mail address and SMTP server address are correct. [. . . ]