User manual SANYO DP50710

[. . . ] Este manual le indica las conexiones básicas y las instrucciones de funcionamiento de dos modelos (Color MPX-CD162, Blanco y negro DP50710). À propos de ce manuel · Avant d'installer et d'utiliser cet appareil, veuillez lire ce · manuel attentivement. Assurez-vous de le garder à portée de la main pour référence ultérieure. Ce manuel couvre les instructions de branchement et d'utilisation de base pour deux modèles (couleur MPX-CD162, noir et blanc DP50710). PRECAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Declaration of Conformity MPX-CD162/ DP50710 SANYO SANYO FISHER COMPANY 21605 Plummer Street, Chatsworth, California 91311 Telephone No. : (818) 998-7322 · This device complies with Part 15 of the FCC Rules. [. . . ] (Default setting) REAL: If using a real time VCR. MODE2: The live pictures from the camera for which programmed recording is set are recorded together with the live pictures from the other cameras. OFF: Programmed recording will not be done. (Default setting) REC SPEED The recording speed settings on this unit correspond to recording durations on a T-120 tape. With a timelapse VCR Set the recording speed to match the recording speed of the timelapse VCR. The available speeds are: 2 (2H) (Default setting), 12 (12H), 24 (24H), 48 (48H), 72 (72H), 96 (96H), 120, 168, 240, 360, 480, 720, 960 (960H) With a real time VCR Set the recording speed to match the recording speed of the real time VCR. The available speeds are: 6 (6H) (Default setting), 18 (18H), 30 (30H), 48 (48H), 72 (72H), 96 (96H), 120, 168, 240, 360 , 480, 720, 960 (960H) NOTE: Real time VCRs speed is based on a T-160 cassette tape. When setting this unit to 6H, 18H or 30H, refer to the table 1 for the speed correspondence, and select the speed on the VCR accordingly. NOTE: · · · · Programmed recording of multiple cameras is done by switching to each camera in order. In the (CAMERA SET) menu, set for each camera if programmed recording is to be conducted or not (see page 36). The recording mode set here is the same as the ACTIVE REC recording mode (see page 34). The programmed recording mode is the normal recording mode applied to the camera, while the active recording mode will modify the recording mode for the camera when an external alarm or a video sensor trigger is received. Any camera for which programmed recording is turned off, will not be recorded when an external alarm or a video sensor trigger is received. · Repeat step 2, until all the settings are as desired. Press the l button to go to the (SENSOR SET) menu, or Press the MENU button to go to the next menu screen, or Press the EXIT button to exit the menu display. (B) (D) 2 (ALARM SET) DURATION 10 S RETRIGGER OFF BUZZER ON DATA ON MON. 1 OUT FULL DOUBLE ALARM LAST MON. 2 OUT OFF (SENSOR SET) SENSOR ALARM OFF DURATION 10 S ALARM SET menu DURATION (Default setting: 10 S) The available durations are (seconds): 1, 2, 3, 4, 5, 10, 20 (in 10 seconds increments). . . 180, CC, NC, INDIV. , OFF CC: The alarm will go on as long as the alarm signal is received (minimum 1 second). NC: The alarm will continue until reset. INDIV. :The alarm duration will be as set for each of the cameras. NOTE: If the "INDIV. " setting is used, in the (CAMERA SET) menu, enter the desired alarm duration for each camera (see page 38). (CAMERA SET) NO. 01 TITLE 01 -------PROGRAM REC AL. DURATION MON. MASK SEQUENCE DAY OFF 10 S OFF 1S NIGHT OFF 10 S OFF 1S (A) FULL (Default setting): If an alarm trigger is received, the picture from the camera corresponding to the alarm input will be displayed full screen. · DOUBLE ALARM (Default setting: LAST) When using the "FULL" setting at the "MON. 1 OUT" line, the following settings are possible. LAST: When triggers from multiple cameras are received in full screen mode, the picture from the camera of the last alarm received is displayed. FIRST: When triggers from multiple cameras are received in full screen mode, the picture from the camera of the first alarm received only is displayed. Camera pictures from subsequent alarm triggers will not be displayed. SWITCH: When triggers from multiple cameras are received in full screen mode, the picture from each concerned camera will be displayed sequentially at 1 second interval. (B) MULTI16: When an alarm trigger is received, the display will switch to a 16 divisions screen. [. . . ] Set the address using DIP switches 1 to 7. Example: · If the address is 1, set switch 1 to the ON side (up) · If the address is 10, set switches 2 and 4 to the ON side (up) · If the address is 127, set all the switches to the ON side (up) Set the DIP switch 9 up ([485] position). Set the terminator using DIP switch 10 2. 3. English 49 INTERFACE SPECIFICATIONS INFORMATION GATHERING COMMANDS STATUS SENSE(D7) When this command is sent from the computer, this unit will send a 5-byte response (see Table 1). Bit Bit state information 1011: Channel 12 1100: Channel 13 1101: Channel 14 1110: Channel 15 1111: Channel 16 (Menu display) 0001: (LANGUAGE/LANG. /IDIO. ) menu 0010: (CLOCK SET) menu 1000: (VCR SET) menu 0100: (ALARM SET) menu 0101: (ACTIVE REC SET) menu 0110: (MONITOR SET) menu 0011: (CAMERA SET) menu 1110: (POSITION SET) menu 0111: (DISPLAY SET) menu 1001: (ALARM DATA) menu RXD TXD D7 d1 d2 d3 d4 d5 STATUS SENSE(D7) byte assignment (Table 1) Fourth and fifth bytes are reserved. [. . . ]