User manual SANYO EC503

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. [. . . ] Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . Resets the PC adjustments to the previous levels. Mode Store . . . . . . . . . . . . . . Stores the PC adjustment values. [Mode1 - Mode5] from the pull-down menu. Mode Free . . . . . . . . . . . . . . . . Clear the PC adjustment values. [Mode1 - Mode5] from the pull-down menu. 70 Setting up the projector Setting up the projector Click Setting on the main menu. This function is to set up the projector. Select the sub menu [Screen setting], [Setting 1] or , [Setting 2] and then set up each setting. Item Description Screen . . . . . . . . . . . . . . . . . . . . . . . . Switches the screen mode. There may not be available mode depending on the input mode as shown in the table below. Screen mode Input source Video 4 * 4 * 4 4 Computer 4 4 4 4 4 4 Normal True Wide Full Digital zoom+ Digital zoom­ The mark "4" indicates the available screen mode in the selected input source system. The error message appears when the disabled screen mode indicated with "*" is selected. 71 Chapter 7 Controlling the projector Item Description Language . . . . . . . . . . . . . . . . . Sets the language display of projector's on-screen display menu. Auto setup . . . . . . . . . . . . . . . Executes the Auto PC Adj, and Input Search function below according to the each setting after clicking Start button. Input Search . . . . . . . Sets the auto-input signal detection mode. Sets all of the projector control items to the factory default setting except the following items. Value, PJ time, Filter time, PIN code lock and Logo PIN code lock. P-TIMER . . . . . . . . . . . . . . . . . . . . . Switches the P-TIMER display. Stops P-TIMER indication 73 Chapter 7 Controlling the projector Timer setting This page is to set the timer to turn the projector off or on at a programmed day/date and time. Click Timer on the main menu. "---" will appear on the current time when the time is not set up correctly. Present time set on the projector Select date Select day Set execute time Event action How to set the timer 1 Set a day or date To set the timer event at the same time everyday or every week, Select day entry with radio button and then select desired day from the pull-down menu button. The selectable days are as follows: - Same time everyday - Every week (days from Monday to Sunday) To set the timer event on specified date, select date entry with radio button and then type the date with (Year/Month/Date) format. Ex. : Type [2007/12/20] if you specify [December 20, 2007]. This projector does not provide the built-in battery. The date and time information are lost when the projector turns off (when "Eco" is set for the stand-by mode (Refer to p. 72)), or the network configuration is reset, or the input mode "Wired" or "Wireless" is turned. The timer function is disable until time is set up correctly. When using the NTP address for time setting, the current time is acquired at the projector starting up and the timer function is activated after finishing the time setting correctly. 74 Timer setting 2 Set an execute time Type the time with (Hour:Minute) and 24 hours format. Ex. : Type [18:25] if you specify [PM 6 o'clock and 25 minutes]. 3 Select an event action Event Action Select an event action from the pull-down menu. ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The files in the FTP server must be optimized JPEG and converted by the File Converter 1 or 2. There are several limitations for image file name and program name. Please check file names and program names (+p. 119). Make sure that your computer is not using the firewall function. [. . . ]