User manual SANYO HEC-DR8700K

[. . . ] INSTRUCTION MANUAL HEC-DR8700 Massage Lounger CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . 58 HOW TO PLACE THE MASSAGER . . . . . . . . . . . . . . . 9 HOW TO INSTALL THE STAND . . . . . . . . . . . . . . . . . . . . . 10 PRIOR TO USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not attempt to adjust the foot rest slide while reclining. If this is not done, accidents or injury may occur. Do not attempt to stand on the foot rest when the foot rest slide position and angle are not completely returned to the home positions. If this is not done, the user may fall over, resulting in an accident or an injury, and the floor may be damaged. To return the massager to the home position, press the HOME POSITION button. The HOME POSITION button lights up and the chair automatically returns to its home position. The foot rest is raised first, and then lowers completely. Foot rest Back rest 15 FEATURES OF COURSES WHOLE BODY SENSOR AUTOMATIC COURSES Features of courses Automatic massages based on the degrees of stress and stiffness measured by sensors prior to massaging. Massages using a whole body Sensor automatic course program based on the degree of stiffness detected by sensors. (See page 17-20) Massaging on the degree of stress and stiffness detected by sensors Sub-courses Features of program Fully automatic massage based on the degrees of stress and stiffness In stress measurement mode, only air massage of your legs is performed. FULL AUTO STIFFNESS RECOVERY RELAX QUICK Shiatsu massage to counteract stiffness Tapping massage to ease muscle fatigue Kneading massage to relax the whole body Short massage to promote blood circulation (Reduced time course) The degree of stress and stiffness are measured by placing your fingers (hand) on the sensors. Massaging of each course is possible without placing fingers (hand) on the sensor. In this case the degree of stress and stiffness is not detected. AUTOMATIC COURSES Easy 1 or 2-button operation Massages automatically by effective combination of gripping, kneading up, kneading down, tapping, combo (tapping and kneading), shiatsu, full stretching, partial stretching, focus stretching, and lower body (air) massage. (See page 21-22) Features of program Massages mainly the neck and shoulders Massages mainly the waist and lower back Air massage of the whole body Stretch to relax the whole body Sub-courses NECK & SHOULDER LOWER BACK COMFORT AIR COURSE STRETCH MANUAL COURSES Full programable upper and lower body massage Massages with your own adjustment of massage types such as gripping, kneading up, kneading down, tapping, combo (tapping and kneading), shiatsu, full stretching, partial stretching, focus stretching, and lower body (air) massage. (See page 23-27) Features of program Multiple roller massages (for upper body) and air massages (for lower body) are available. When the massaging rollers detach from the body during the Whole Body Sensor Automatic Course or the Automatic Course, the body pressure sensor will work to stop the operation by pulling back the massaging rollers for safety. In such a case, begin the operation again from the start. felt To stop the massage during operation. If you have stopabnormal physical sensation or want to the massager immediately. Press the OPERATION ON/OFF button. All the massaging will stop. (The massaging rollers are moved to the upper position and remain in that position. ) Press the INSTANT STOP button. Press the button for the current operation. The massaging that corresponds to the pressed button will stop. (The Massaging rollers will stop at that point. ) All the massaging will stop and the lamp of the remote control will turn off. When you want to restart massaging, press the OPERATION ON/OFF button. (The massaging rollers move to the upper position and remain in that position. ) After the movement, repeat the operation to begin a massage. 16 MASSAGING (WHOLE BODY SENSOR AUTOMATIC COURSES) 1 4 5 6 3 2 4 1 Press the OPERATION ON/OFF button. When the button is pressed, the lamps of the sole warmer and remote control will illuminate, and the sole warmer will turn on. When the foot rest is fully lowered, the foot rest will rise a little. When the massaging rollers are not located in the upper section, the massaging rollers will move to the upper section and stop. [at the origin] (During the movement, the icon of "ORIGIN" on the remote control flickers. ) 2 Open the cover of the remote control. (See page 23) 3 Turn the sole warmer ON/OFF. Press the SOLE WARMER button. The sole warmer mode changes as follows each time the button is pressed. The current mode can be identified by the status of the corresponding lamp (when the sole warmer is on, the SOLE WARMER HIGH or LOW lamp is lit). HIGH (Lit) If LOW (Lit) (Neither lamp is lit) OFF you feel that the sole warmer is too hot, turn it off by pressing the SOLE WARMER button. * When the room temperature is low, such as in winter, it takes some time to warm up or you may not feel warm. When the sole warmer is in LOW mode, the heating temperature is adjusted automatically based on the room temperature. Heating temperature is set to LOW. Room temperature is high Room temperature is low Heating temperature is set to HIGH. * LOW mode saves power consumption by approximately 15 % (compared to HIGH mode, at room temperature of 25°C (77 ) 4 Adjust the angle and position of the back rest and the foot rest. (See page 12-15) 17 5 Press the desired Whole Body Sensor Automatic Course button. The button that is blinking indicates the currently selected Whole Body Sensor Automatic Course. [. . . ] 1 cm (3/8") /one press of button Approx. 120170° Back rest: Motor-driven type (Linked with foot rest) Foot rest: Motor-driven type (Foot rest only) Seat surface: Motor-driven type (Linked with back rest and foot rest) (3 stages) Approx. 1127 kPa There is a slight difference according to the part. Do not use the massager on other than the designated voltage. 34 SANYO MASSAGE LOUNGER LIMITED WARRANTY OBLIGATIONS (USA ONLY) HEC-DR8700 In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Factory Service Center at the user's expense, unless specifically stated otherwise in this warranty. If you need assistance with product operation, authorized service center referral, service assistance, problem resolution, or parts and accessories availability; you may contact us by: A. Visiting www. sanyoservice. com on a 24 hr/7 days a week basis or B. [. . . ]