User manual SANYO KBC-9V3U

[. . . ] CAUTION: Changes or modifications not expressly approved by the manufacturer may void the user's authority to operate this equipment. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. Location For safe operation and satisfactory performance of your unit, keep the following in mind when selecting a place for its installation: Shield it from direct sunlight and keep it away from sources of intense heat. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. [. . . ] Enter the approximate number of the desired image. Press the [ ] and [ ] buttons to change the number. Press the [ ] button to move the cursor. 3 Press the [ ] button. The <TIME/DATE SEARCH> screen is displayed. (1) (2) (3) (4) (5) 5 Press the [ ] button. (1) RECORDING TOP: Displays the date and time of the video recorded first. (2) RECORDING END: Displays the date and time of the video recorded last (most recent video). (3) SEARCH: Enter the date and time of the video to play back. (4) PREVIEW: Select this item to display the preview screen. (5) VIEW: Select this item to play back the video on the quad screen. (continued) OPERATION The page with the input alarm number is displayed. Date and time search Follow the steps below to play back a video recorded on the hard disk by specifying its date and time. [ ] button [ ] button [SEARCH] button [ ] button 1 2 Press the [SEARCH] button while the digital video recorder is recording or stopped. The <SEARCH> screen is displayed. Press the [ ] or [ ] button to select "TIME/DATE SEARCH". 24 e00_VDH_M814. book Page 25 Thursday, October 28, 2004 9:59 AM SEARCHING FOR RECORDED VIDEOS 4 Press the [ ] button, and set the date and time to search. Example: To search for the video from October 26 2004 20:00 6 Press the [ ] button to select "VIEW", then press the [ ] button. The preview screen image is played back in the quad screen. HI A 10- 2 6 - 0 4 2 0 : 0 0 : 0 0 (1) (2) (3) (4) (5) OPERATION (1) Press the [ month). ] or [ ] button to select "10" (the ] or [ ] ] ] The retrieved video can be displayed in the quad screen format without displaying the preview screen by entering the date and time, and selecting "VIEW". You can use the button operations to pause, fastforward or perform other operations on retrieved videos being played back. If this data is less than 1 MB in size, "-----" is displayed and "COPY START" will not be possible. (4) START TIME: Specifies the date and time for the start of copying. (5) END TIME: Specifies the date and time for the end of copying. A date and time earlier than "START TIME" cannot be specified. (6) COPY START: Starts copying when selected. (7) Preview: Displays the image corresponding to the date and time set by "START TIME" or "END TIME". OPERATION When copying has been completed, "COPY FINISHED" appears, and the screen will return to the live video display when any button is pressed. A video is copied to the CompactFlash card, CD-R/RW as follows. Example: Copying from 10:15 on April 25th with a DVR NAME of "FRONT" CompactFlash card, CD-R/RW FRONT (1) 0425-1015. mp2 0425-1015-1. mp2 0425-1015-2. mp2 (2) 3 Press the [ ] and [ ] buttons to specify "START TIME" and "END TIME", and then press the [ ] button. (1) A folder is created for the DVR NAME on the CompactFlash card, or CD-R/RW. (2) A file is created inside that folder with its name reflecting the date and time. If "DVR NAME" has not been set, the name "KBC-9V3U" will be used when creating folders. The character "+" will be used to replace any slash (/), semi-colon (;), asterisk (*), period (. ), or colon (:) characters appearing in "DVR NAME". [. . . ] To cancel formatting, select "NO". To exit Press the [EXIT/OSD] button. The display returns to the normal screen. SETTINGS 65 e00_VDH_M814. book Page 66 Thursday, October 28, 2004 9:59 AM APPENDIX 1. CONTROL TERMINAL SPECIFICATIONS Connecting cables to the control terminals Cable 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Terminal No. Name RS-485A RS-485B C REMOTE C Signal RS-485 RS-485 Function To RS-485 terminal signal A*1 To RS-485 terminal signal B*1 Common 1 2 3 4 5 6 Flat-blade screwdriver (1) Push in the lock pin with a flat-blade screwdriver. (3) Pull out the lock pin with a flat-blade screwdriver. The cable is now secured in place. Resistance ladder connection Remote Control terminal Common Input for clock setting Normal open, CLOCK ADJ IN Low level active CLOCK ADJ OUT C SERIES REC IN Normal open, Low level active Normal resistance 5V DC/57k, Low level active System controller connections The connections for a system controller are shown below. [. . . ]