User manual SANYO LNS-T02K LENS REPLACEMENT AND INSTALLATION PROCEDURE
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SANYO LNS-T02K. We hope that this SANYO LNS-T02K user guide will be useful to you.
Lastmanuals help download the user guide SANYO LNS-T02K.
Manual abstract: user guide SANYO LNS-T02KLENS REPLACEMENT AND INSTALLATION PROCEDURE
Detailed instructions for use are in the User's Guide.
[. . . ] LNS-W02/T02 LNS-W02K/T02K Series
LENS REPLACEMENT AND INSTALLATION PROCEDURE
NOTES ON LENS INSTALLATION
Lens installation should be performed by the qualified service personnel. It should be followed by this procedure precisely. Before attempt to install the lens, confirm the model number (both the LCD projector and the lens) and use the proper lens. [. . . ] A D
B
D
Fig-1
LOWER LENS COVER
LENS COVER
In case figure-2 cabinet. Remove 4 screws of the lens cover and remove the lens cover.
Fig-2
2
IN CASE OF MODEL WITHOUT LENS REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-3) Remove 2 screws and pull down the plate. (At the step 5 , insert the light-block sheet in the same position as the removed cover plate has been placed. Two screws are not used. ) Use the light-block sheet included with lens.
Set the light-block sheet, so that the large rounder side is set over the lens. LIGHT-BLOCK SHEET
SCREWS
COVER PLATE
Fig-3
Figure shown inside of the cabinet.
LENS MOTOR (D)
IN CASE OF MODEL WITH LENS REMOVE THE LENS. Remove the connector "K16B" of the circuit board. Loosen the A, B, C wire holder and remove the lens motor lead. Remove screws D (4 screws) which fastens the lens and remove the lens.
A
(D)
(D)
(D)
C B LENS MOTOR LEAD CONNECTOR " K16B"
Fig-4
(D)
LENS MOTOR (D)
A
(D)
(D)
C B
3
INSTALL THE LENS. (See figure-4, 5)
CONNECTOR "K16B"
This part wiring should not be tightened.
LENS MOTOR LEAD
1. Remove protective caps (front and back ) on the lens. Mount the lens at the lens mounting bracket with screws (4 screws) included with the lens. Use the driver included with the lens to fasten the screws . (After using, save it for latter use. ) (See figure-5) 3. [. . . ] (See figure-8) If the installation of the light-block sheet is incorrect, there will be the space between lens and the lens cover, so that it will be the cause of leakage of light or the dust entering at the main cabinet. 1. Insert the upper part lens cover and fix them with screws A (4 screws). 2. Insert the lower part lens cover and fix them with screws B (2 screws).
B A
LOWER LENS COVER
Fig-7
Removed lens cover in figure-2 is not used, keep the cover for possible reuse when current lens is used.
Set the light-block sheet, so that the large rounder side is set over the lens.
Insert into the slot. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SANYO LNS-T02K
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SANYO LNS-T02K will begin.
