User manual SANYO PDG-DWL100

[. . . ] Multimedia Projector MODEL PDG-DWL100 Owner's Manual Table of Contents Table of Contents Usage Notice Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Network Setting Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Security Setting Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Alert Setting Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Brightness Adjust the brightness of the image. Press the Press the Contrast to darken image. to lighten the image. The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Press the Press the Color Press the Press the to decrease the contrast. to increase the contrast. Adjust a video image from black and white to fully saturated color. to decrease the amount of color in the image. to increase the amount of color in the image. English English 23 User Controls Tint Adjust the color balance of red and green. Press the to increase the amount of green in the image. Press the to increase the amount of red in the image. Sharpness Adjust the sharpness of the image. Press the to decrease the sharpness. White Peaking Use the white peaking control to set the white peaking level of DMD chip. 0 stands for minimal peaking, and 10 stands for maximum peaking. If you prefer a stronger image, adjust towards the maximum setting. For a smooth and more natural image, adjust towards the minimum setting. Color Temp. Adjust the color temperature. At higher temperature, the screen looks colder; at lower temperature, the screen looks warmer. Gamma This allows you to choose a gamma table that has been fine-tuned to bring out the best image quality for the input. 24 English User Controls Screen Keystone N ot e The bottom side of OSD menu might be out of display when user adjusts keystone value, under the status of low resolution signal input and different aspect ratio setting. To solve this problem, please adjust keystone value in "Aspect Ratio" of "4:3" then switch back to your desired aspect ratio. Adjust image distortion caused by tilting projector. H-position (Horizontal Position) Press the to move the image left. V-position (Vertical Position) Press the to move the image down. Aspect Ratio Use this function to choose your desired aspect ratio. 4:3 This format is for 4:3 input sources not enhanced for Widescreen TV. 16:10 This format is for 16:10 input sources, like HDTV and DVD enhanced for Widescreen TV. Native This format displays the original image without any scaling. English English 25 User Controls Mounting Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen. Front-Ceiling When you select this function, the projector turns the image upside down for ceiling-mounted projection. Rear-Ceiling When you select this function, the projector reverses and turns the image upside down at same time. You can project from behind a translucent screen with ceiling mounted projection. 26 English User Controls Setting Input Search When this function is turned "On", the projector will search for other signals if the current input signal is lost. [. . . ] Please, help us to conserve the environment we live in! English English 55 Appendices Serial Control Interface This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port. 1. Connect a RS-232C serial cross cable to SERVICE PORT on the projector and serial port on the PC. Launch a communication software provided with PC and setup the communication condition as follows: 3. Type the command for controlling the projector and then enter the "Enter" key. [. . . ]