User manual SANYO PLC-WXU700A

[. . . ] Multimedia Projector MODEL Network Supported Wireless LAN IEEE802. 11b/g/n Wired LAN 100-Base-TX/10-Base-T PLC-WXU700A USB Memory Viewer Memory Viewer * Refer to the owner's manuals below for details about network and memory viewer function. Network Set-up and Operation Memory viewer function Owner's Manual Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16. 77 million colors, and matrix liquid crystal display (LCD) technology. Compact Design This projector is designed compact in size and weight. It is easy to carry and installed anywhere you wish to use. - You can project an image on a computer as well as operate and manage the projector via network. [. . . ] Press the SELECT button to compress image size. The projected image can be also compressed by pressing the D. ZOOM - button on the remote control. To exit the Digital zoom +/­ mode, press any button except the D. ZOOM +/- buttons, SELECT and Point buttons. To return to the previous screen size, select a screen size from the Screen Size Adjustment Menu or select an input source from the Input Source Selection Menu (see pages 30-31) again or adjust the screen size with the D. ZOOM +/buttons. Note: · The panning function may not operate properly if the stored Mode in the PC adjust Menu is used (p. 35). · The minimum compression ratio is limited depending on the input signal, when the Keystone function is working or when the custom is selected for the screen size. · True, Full and Digital zoom +/­ cannot be selected when 480i, 575i, 480p or 575p is selected in the PC System Menu (p. 32). · Digital zoom +/- cannot be selected when Full or True is selected. · When Custom is selected, the Digital zoom function is disabled. Note: · When no signal is detected, Normal is set automatically and the Aspect dialog box disappears. · The adjustable range for Scale H/V and Position H/V is limited depending on the input signal. Remote Control POINT buttons SELECT button D . ZOOM + button D . ZOOM - button 39 Video Input Input Source Selection (Video, S-video) Direct Operation Choose Video or S-video by pressing the INPUT button on the top control or the VIDEO button on the remote control. Top Control INPUT button Computer 1 Computer HDMI Remote Control VIDEO button Video S-video Video S-video Network COMPUTER can not be selected when using the COMPUTER IN 2/MONITOR OUT terminal as MONITOR OUT output. Menu Operation 1 Press the MENU button to display the On-Screen Menu. Use the Point buttons to select Input and then press the Point or the SELECT button. Use the Point buttons to select either Video or S-video and then press the SELECT button. Input Menu Video S-video When video input signal is connected to the VIDEO jack, select Video. When video input signal is connected to the SVIDEO jack, select S-video. Video Note: · Network is for the Network function. See the owner's manual of "Network Set-up and Operation" . · When the Input Search function is set to On1 or On in the Auto setup function, the input signal will be searched automatically (p. 48). 40 Video Input Input Source Selection (Component, RGB Scart 1-pin, HDMI) Direct Operation Choose Computer 1 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control; choose HDMI by pressing the INPUT button on the top control or press the HDMI button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below. INPUT button Remote Control Top Control HDMI button HDMI COMPUTER button Computer 1 Computer Computer 1 Computer HDMI Video S-video COMPUTER can not be selected when using the COMPUTER IN 2/ MONITOR OUT terminal as MONITOR OUT output. Menu Operation 1 3 Input Menu Network Press the MENU button to display the On-Screen Menu. Use the Point buttons to select Input and then press the Point or the SELECT button. Use the Point buttons to select Computer 1 and then press the Point button; use the Point buttons to select HDMI, and then press the SELECT button. When Computer 1 is selected, use the Point buttons to select Component or RGB(Scart) and then press the SELECT button. Component When the input source is coming from video equipment connected to the COMPUTER IN 1/COMPONENT IN terminal with a Component-VGA Cable, select Component. When the input source is coming from video equipment connected to the COMPUTER IN 1/COMPONENT IN terminal with a ScartVGA Cable, select RGB (Scart). When the video signal is connected to the HDMI terminal, select HDMI. RGB (Scart) HDMI Note: · Network is for the Network function. [. . . ] (Hz) 60. 02 58. 069 29. 80 60. 19 60. 120 59. 900 59. 954 60. 000 59. 887 60. 00 (Interlace) 60. 00 (Interlace) 50. 00 (Interlace) 59. 94 (Interlace) 59. 94 60. 00 50. 00 59. 95 Note: · The specifications are subject to change without notice. · Depending on your PC settings, the digital signals of your PC may not be projected correctly. In such a case, confirm your PC settings. · When you project a DVI signal, connect the cables, turn the projector on, then select the input. [. . . ]