User manual SANYO PLC-XU300

[. . . ] If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "TROUBLESHOOTING" section at the end of this manual. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. G This projector produces intense light from the projection lens. Do not stare directly into the lens as it could possibly damage your eyes. [. . . ] (Hz) 75. 70 86. 96 (Interlace) 58. 20 58. 30 72. 00 75. 08 75. 06 70. 40 58. 60 60. 00 59. 98 60. 01 67. 19 76. 107 60. 02 75. 025 60. 00 65. 20 75. 60 86. 00 (Interlace) 94. 00 (Interlace) 60. 01 72. 00 66. 00 86. 70 (Interlace) 60. 18 75. 08 75. 08 60. 00 60. 00 (Interlace) 60. 00 (Interlace) 50. 00 (Interlace) 77. 07 NOTE : Specifications are subject to change without notice. 23 COMPUTER INPUT PC ADJUSTMENT AUTO PC ADJUSTMENT Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your computer. Auto PC Adjustment function can be operated as follows. Auto PC Adj. 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon. Press POINT DOWN button to move a red frame pointer to AUTO PC Adj. icon and then press SELECT button twice. This Auto PC Adjustment can be also executed by pressing AUTO PC ADJ. button on Remote Control Unit. PC ADJUST MENU PC ADJUST Menu icon Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by selecting Mode in PC SYSTEM Menu (P22). Refer to step 3 of MANUAL PC ADJUSTMENT section (P26). Move a red frame pointer to AUTO PC Adj. Selected Mode Shows status (Stored / Free) of the selected Mode. Press SELECT button at this icon to adjust "Clamp, " "Display area (H/V)" or set "Full screen. " Press SELECT button at Current mode icon to show the information of computer connected. 25 COMPUTER INPUT Display area Selects area displayed with this projector. Select the resolution at Display area dialog box. Display area H Adjustment of horizontal area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value to match the resolution of image. Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value to match the resolution of image. Full screen Press POINT LEFT/RIGHT button(s) to switch Full screen function to "On" or "Off. " Set "On" to resize the image with 4 x 3 aspect ratio to fit the screen. (note; This function does not work when adjusting Horizontal or Vertical manually. ) NOTE : Fine sync, Total dots, Display area (H/V) and Full screen cannot be adjusted when "1035i (HDTV)" or "1080i (HDTV)" is selected on PC SYSTEM Menu (P22). Press SELECT button at Display area icon and Display area dialog box appears. Display area To store adjustment data. This Mode has parameters being stored. 3 Store To store adjustment parameters, move a red frame pointer to Store icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store to and then press SELECT button. Mode free To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then press SELECT button. Move a red arrow pointer to the Mode that you want to clear and then press SELECT button. [. . . ] (See "SETTING" section on page 35. ) Picture is Left/Right reversed. Some displays are not seen during the Operation. No image. G Check Display feature. (See "SETTING" section on page 35. ) G Check the connection between your computer or video equipment and a projector. (Refer to page 21. ) G When turning a projector on, it takes about 30 seconds to display an image. [. . . ]