User manual SANYO PLCSU22N

[. . . ] Multimedia Projector MODEL PLC-SU22N Owner's Manual INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. TO THE OWNER As the owner of a new Multimedia Projector, you are probably eager to try out your new projector. [. . . ] Close the PICTURE IMAGE ADJUSTMENT Menu. Move the arrow to the item and then press the SELECT button. 3 Move the arrow to "Go!" and press the SELECT button to start the Auto Image function. This adjustment can be executed by pressing AUTO IMAGE button on the Top Control and the Remote Control Unit. Quit Stores the On/Off setting of each item. Closes the AUTO IMAGE ADJUSTMENT Menu. NOTE : The Fine sync. , Total dots, and Picture Position of some computers may not be fully adjusted with the Auto Image Function. In that case, manual adjustment is required to make fine image. (Refer to page 27 to adjust "Fine sync. " or "Total dots" and page 28 to adjust Picture Position. ) PICTURE POSITION ADJUSTMENT The position of the image can be adjusted vertically and horizontally through PICTURE POSITION ADJUSTMENT. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select POSITION and press the SELECT button. The PICTURE POSITION dialog box will appear. Move the image by pressing the POINT UP / DOWN / RIGHT / LEFT buttons. PICTURE POSITION dialog box Press the POINT UP / DOWN / RIGHT / LEFT buttons to move the image 28 COMPUTER MODE PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display the image in desirable size. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT button. Another dialog box PICTURE SCREEN Menu will appear. Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the function that you want to select and then press SELECT button. Move the arrow to the function and press the SELECT button. True To turn the image into its original size select True in the dialog box. When the original image size is larger than the screen size (800 x 600), this projector becomes Digital Zoom mode automatically. Key Stone When the image is distorted vertically, select Keystone in the dialog box. The ON-SCREEN menu and SCREEN ADJUST menu disappears and the message "Keystone" is displayed. Correct the Keystone distortion by pressing the KEYSTONE v/w button or the POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on page 21. Digital Zoom To adjust the image size or pan the image, select Digital zoom in the dialog box. The ON-SCREEN menu and SCREEN ADJUST menu disappears and the message "D. [. . . ] If after following all operating instructions, you find that service is necessary, contact the SFS Corporation in Los Angeles, or the store where you purchased the unit. Give the model number and explain the difficulty. We will advise you how to obtain service. 45 TECHNICAL SPECIFICATIONS Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Panel Resolution Number of Pixels Color System Scanning Frequency Projection Image size (Diagonal) Horizontal Resolution Projection Lens Throw Distance Projection Lamp AV Input Jacks Computer Input Jacks Control Port Jack Monitor Output Jack Computer Audio Input Jack Audio Output Jack Internal Audio Amp Built-in Speaker Feet Adjustment Voltage Power Consumption Operating Temperature Storage Temperature Remote Control Transmitter Multi-media Projector 9. 41" x 3. 54" x 12. 72"(239mm x 90mm x 323mm) (not including Adjustable Feet) 8. 82 lbs (4. 0 kg) 0. 9" TFT Active Matrix type, 3 panels 800 x 600 dots 1, 440, 000 (800 x 600 x 3 panels) PAL, SECAM, NTSC, NTSC4. 43, PAL-M and PAL-N H-sync. 50 ~ 100 Hz Adjustable from 30" to 300" 750 TV lines F 1. 7 ~ 2. 0 lens with f 33. 2mm ~ 43. 1mm Motor zoom and focus 4. 6' ~ 35. 4' (1. 4 m ~ 10. 8 m) 150 W RCA Type x 1 (Video, Audio R and L) and DIN 4 pin (S-Video) x 1 (VGA) HDB 15 Terminal x 1 DIN 8 pin x 1 (VGA) HDB 15 Terminal x 1 Mini Jack (stereo) Mini Jack (stereo) 1W RMS (Monaural) 1 speaker, 1. 57" x 1. 18" (40mm x 30mm) 0° to 10° AC 100 ~ 120 V, 50 / 60 Hz 2. 5 A (Max. [. . . ]