User manual SANYO PLCXU21N

[. . . ] Multimedia Projector MODEL PLC-XU21N Owner's Manual INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. TO THE OWNER As the owner of a new Multimedia Projector, you are probably eager to try out your new projector. [. . . ] When selecting Computer, this projector automatically tunes to the incoming signal and projectors the proper image without any special setting. (Setting of the Computer System may be required when connecting some computers. ) Note : The projector may provides the messages below. SYSTEM BOX It displays the SYSTEM being selected. Go to PC adj. The projector cannot discriminate or detect the input signal from the computer. Adjust and set the computer system manually. (Refer to page 24. ) No signal There is no signal input from the computer. Make sure the connection of the computer and the projector is set correctly. (Refer to TROUBLESHOOTING on page 35. ) SELECT COMPUTER MODE MANUALLY To set the Computer system manually, select the mode on the ONSCREEN MENU. The system being selected. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Another dialog box COMPUTER SYSTEM Menu will appear. Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the system that you want to set, and then press SELECT button. The systems on this dialog box can be selected. It closes the SYSTEM Menu. 22 COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and less than 140 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 ­­­­­­­­ ­­­­­­­­ VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 VGA 7 MAC LC13 MAC 13 RGB RGB SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 SVGA 12 MAC1 6 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 H-Freq. (kHz) 31. 47 31. 47 31. 47 37. 86 37. 86 37. 50 43. 269 34. 97 35. 00 15. 734 15. 625 35. 156 37. 88 46. 875 53. 674 48. 08 37. 90 34. 50 38. 00 38. 60 47. 90 32. 70 38. 00 49. 72 48. 36 68. 677 60. 023 56. 47 60. 31 48. 50 44. 00 63. 48 36. 00 V-Freq. (Hz) 59. 88 70. 09 70. 09 74. 38 72. 81 75. 00 85. 00 66. 60 66. 67 30 25 56. 25 60. 32 75. 00 85. 06 72. 19 61. 03 55. 38 60. 51 60. 31 71. 92 51. 09 60. 51 74. 55 60. 00 84. 997 75. 03 70. 07 74. 92 60. 02 54. 58 79. 35 43. 59 ON-SCREEN DISPLAY RESOLUTION 1024 x 768 1024 x 768 1024 x 768 (Interlace) XGA 10 XGA 11 XGA 12 XGA 13 XGA 14 XGA15 MAC 19 MAC21 SXGA 1 SXGA 2 SXGA 3 SXGA 4 SXGA 5 SXGA 6 SXGA 7 SXGA 8 SXGA 9 SXGA 10 SXGA 11 SXGA 12 SXGA 13 SXGA 14 SXGA 15 SXGA 16 SXGA 17 SXGA 18 SXGA 19 MAC MAC HDTV720p HDTV1035i HDTV1080i H-Freq. (kHz) 62. 04 61. 00 35. 522 46. 90 47. 00 58. 03 60. 24 68. 68 64. 20 62. 50 63. 90 63. 34 63. 74 71. 69 81. 13 63. 98 79. 976 60. 00 61. 20 71. 40 50. 00 50. 00 63. 37 76. 97 61. 85 46. 43 63. 79 75. 00 80. 00 45. 00 33. 75 33. 75 V-Freq. (Hz) 77. 07 75. 70 43. 48 58. 20 58. 30 72. 0 75. 08 75. 06 70. 40 58. 60 60. 00 59. 98 60. 01 67. 19 76. 107 60. 02 75. 025 60. 00 65. 20 75. 60 43. 00 47. 00 60. 01 72. 00 66. 00 43. 35 60. 18 75. 08 75. 08 60. 00 60. 00 60. 00 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 870 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 960 1152 x 900 1152 x 900 1280 x 1024 (Interlace) 1280 x 1024 (Interlace) 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 (Interlace) 1280 x 1024 1280 x 1024 1152 x 900 1280 x 1024 (Interlace) 1280 x 1024 1280 x 960 1280 x 1024 ­­­­­­­­ ­­­­­­­­ ­­­­­­­­ NOTE : Specifications are subject to change without notice. 23 COMPUTER MODE PC ADJUSTMENT This Projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ the special signal formats which are different from the standard ones and may not be tuned by Multiscanning of this projector. If this happens, the projector cannot reproduce a proper image and the image is recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match with those exceptional signal formats and the projector has five independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT RIGHT/LEFT buttons to select PC ADJUST and press the SELECT button. Another dialog box "Where to reserve" Menu will appear. In this dialog box, you can store the parameter into the area from "Mode 1" to "Mode 5. " When memorizing the new computer parameter, select the Mode with the message of "Free" by pressing the POINT UP/DOWN buttons and the SELECT button. [. . . ] No image. q Check Display feature. (See "SETTING" section on page 31. ) q Check the connection between the computer or video equipment and the projector. q When turning the projector on, it is about 30 seconds to display the image. q Check the system that you select is corresponding with the computer or the video equipment. q Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C). [. . . ]