User manual SANYO PLV-Z4

[. . . ] Multimedia Projector MODEL PLV-Z4 Owner's Manual Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 1. 07 billion colors, and matrix liquid crystal display (LCD) technology. Short Throw & Wide-Range Zoom Lens This projector is equipped with 2x Short Throw & WideRange Zoom Lens capable of throwing a 100" diagonal image from a distance of of 9. 8' (3. 0 m) to 20. 0' (6. 1 m). Automatic Slide Shutter The automatic slide shutter protects the lens from dust and scratches. It opens and closes automatically as you press the POWER ON-OFF button. Lens Shift The Lens Shift function provides the projector greater installation flexibility. You can use the projector at desired places without a distorted image. [. . . ] After adjusting, press the OK button to go to the Color management list. COLOR MANAGEMENT LIST (continued) In the COLOR MANAGEMENT LIST, the adjusted color data are check marked reflecting the changes in the projected image. (See the previous page. ) You can also decide whether or not to apply the adjusted color data in the list to a projected image. Clear the check mark if you do not want to apply the adjusted color data; select the check mark and then press the OK button. If you want to readjust the color, select a color data box in the list and press the OK button. The COLOR SELECTION window will appear and you can readjust the color. If you want to delete a particular color data in the list, select the DEL box of the color data and then press the OK button. Select [Yes] and then press the OK or Point 8 buttons. Reset To reset the adjusted data, select Reset and press the Point 8 or OK buttons. Select [Yes] and then press the OK or Point 8 buttons. All adjustments return to their previous figures. You can also reset the adjusted data with the RESET button on the remote control. Store To store the adjusted data, select Store and press the Point 8 or OK buttons. Choose one of the four (4) image levels with the Point ed buttons and press the OK or Point 8 buttons. Select [Yes] and then press the OK or Point 8 buttons. To exit the Image Level Menu, press the OK or Point 8 buttons at the Quit icon. The stored data can be called up by selecting "User image 1 ~ 4" in the Image Level Selection on page 27. COLOR SELECTION Color management pointer Use the Point ed 7 8 buttons to move the pointer to a spot where you want to adjust the color and then press the OK button. The COLOR SELECTION window will appear. After adjusting Color level, Color phase and Gamma, press the OK button. Go to the Color management list (see the previous page). To store the adjusted data, exit the Color management mode and move on to "Store" in the Image adj. Menu. Press the Point 8 or OK buttons at this icon to store the adjusted data. The Image Level Menu will appear. Note: · If you turn off the POWER without storing adjusted settings, all the adjusted settings will be reset. [. . . ] The time when the LAMP REPLACE indicator should light is depending on the lamp mode. See pages 46 and 47. 49 Appendix Menu Tree Input Video / S-Video Component 1 Component 2 HDMI Auto PAL SECAM NTSC NTSC 4. 43 PAL-M PAL-N Quit RGB(Analog) RGB(Scart) Quit Computer Image Creative cinema Pure cinema Natural Living Dynamic Powerful Vivid User image 1 User image 2 User image 3 User image 4 Image adj. Brightness Contrast Color Tint Color temp. Red Green Blue Sharpness Lamp Control Gamma Progressive Lens iris Advanced menu Reset Store -31 ~ +31 -31 ~ +31 -31 ~ +31 -31 ~ +31 High Mid Low 1 Low 2 Low 3 User -31 ~ +31 -31 ~ +31 -31 ~ +31 -7 ~ +7 Normal Auto 1 Auto 2 Eco -7 ~ +7 Off L1 L2 Film -63 ~ 0 Lamp iris Auto / Open / Close Auto black stretch Off / L1 / L2 / L3 Contrast enhancement Off /L1 / L2 / L3 Transient improvement Off / L1 / L2 /L3 Color management Gain R/G/B -15 ~ +15 Offset R/G/B -15 ~ +15 Gamma R/G/B -5 ~ +5 Yes / No User image 1 User image 2 User image 3 User image 4 Quit 50 Appendix Picture adj. Overscan Horizontal Vertical Auto adj. Fine sync Total dots 0 ~ +10 -100~ +100 -100~ +100 0 ~ +31 -100 ~ +100 Setting Language - - - When 480i / 575i input, -8 ~ +8. Screen Full Full through Zoom Caption in Normal Normal through Natural wide 1 Natural wide 2 Advanced menu Menu Position Keystone Mounting PAL SECAM NTSC NTSC4. 43 PAL-M PAL-N 480i 480p 575i 575p 720p 1080i D-VGA D-480i D-480p D-575i D-575p D-720p D-1080i Resolution for PC input ---Unknown English German French Italian Spanish Portuguese Dutch Swedish Finnish Polish Hungarian Romanian Russian Chinese Korean Japanese Quit On / Off Information Signal Rear HDMI setup Blue back Display Logo Power off confirmation Capture Power management Remote control Shutter demo Cleaning Panel adjustment Off Ceiling Wall On / Off L1 L2 On / Off On Countdown Off Off User Default Off On / Off Yes / No On / Off Code 1 Code 2 Start Test pattern R Test pattern G Test pattern B Check pattern Yes / No Yes / No H-sync freq. Lamp Time Lamp counter reset Factory default 51 Appendix Compatible Computer Specifications PLV-Z4 can basically accept the signal from all computers with V, H-Frequency mentioned below and less than 100 MHz of Dot Clock. System mode 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 400 640 x 480 720 x 400 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 848 x 480 1024 x 768 1024 x 768 1024 x 768 1024 x 768 H-Freq. [. . . ]