User manual SANYO POA-PN10

[. . . ] POA-PN10 Preparation Installation POW ER Basic Setting and Operation Controlling the Projector Controlling the Multi-Projectors Use of Serial Port Appendix INSTALLATION and OPERATION of the PJ-Net Organizer This PJ-Net Organizer is an optional product to control and set up a projector via a network. Attach this product to the projector and connect a network cable. By accessing the connected projector using the web browser on your computer, the projector can be controlled and set up remotely. This product is only used for SANYO projectors that have a terminal for the PJ-Net Organizer. [. . . ] The RGB analog input of the Computer 2 can be used through the VGA terminal on the network unit. Select a source mode with pull down menu. Select a source with radio buttons. 38 Control the projector PC Adjustment This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. The available parameters and operation are listed below. Adjustment Items Auto PC adjustment Fine sync Total dots Position Comment Operation Press the Start button to start automatic adjustment. Press the - or + button repeatedly to adjust the fine sync. Press the - or + button repeatedly to adjust the number of total dots in the horizontal period. Press the Up, Down, Left or Right button repeatedly to adjust the picture position. Type the comment in the text area and then press the Save button. These parameters will appear only when the computer input mode is selected. Network Unit OWNER'S MANUAL 39 ENGLISH Controlling the Projector SYSTEM Adjustment This function is to select the color system of video signal or scanning system of component signal input to the projector. Select a system with the radio buttons to match the color system or scanning system of input source, and then press the Set button. The available systems and operation are listed below. Adjustment items Color system (VIDEO/S-VIDEO Input) Operation AUTO: Automatically detect the color system of input signal. PAL, SECAM, NTSC, NTSC4. 43, PAL-M, PAL-N: Manually select the color system of input signal. AUTO: Automatically detect the scanning system of input signal. 1080i, 1035i, 720p, 575p, 480p, 575i, 480i: Manually select the scanning system of input signal. Scanning system ((Y, Cb/Pb, Cr/Pr Input) Available selection when the VIDEO/S-VIDEO input Available selection when the Y, Cb/Pb, Cr/Pr input These selections will not appear when the source mode is selected to the computer mode. 40 Control the projector Image Adjustment This function is to adjust the projected picture image and set the image mode. For selection of image mode, select desired image mode among the "Standard", "Real", "Cinema", "Image1", "Image2", Image3" and "Image4" with the "Image Adjustment Mode" Current set pull down button and then press value the Set button. The setting items are switched automatically according to selected input mode, computer or video input. To adjust the controls, press the + or - buttons to increase or decrease the value, or enter the value directly onto the text area of the control and then press Set button. The adjustment items and operation are listed below. The value next to each control represent the current control value and status. The mode "Image1" to "Image4" can be stored as your preferred image mode through "Save Adjustment" item located on lower part of the page. Select an image number from the pull down menu button and then press the Save button. To cancel your change, press the Return button. The "Original Mode" is to indicate which * The displayed adjustment items may differ from the actual depending on the funcimage mode are applied to the user preset tions of projector you use. modes "Image1" to "Image4". Adjustment items Operation Image adjustment mode Select image mode among the Standard, Real **, Cinema*, Image1 to Image4 with pull down button menu . Adjustment items Contrast, Brightness, Sharpness*, Gamma, White Balance, Color Temperature, Tint*, Color*, Noise Reduction*, Progressive* * Controls for video input, ** Controls for computer input Comment Type the comment in the text area and press the Save button. [. . . ] A Make sure that the registered E-mail address and SMTP server address are correct. If the SMTP server is located in your LAN (Local Area network), the address should be set to the SMTP server in your LAN. The SMTP server located outside of your LAN may not be available for security reason. For further information please contact your network administrator (p. 32). [. . . ]