User manual SANYO SLIM-1600_OM_ENGLISH.PDF

[. . . ] THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED. Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. [. . . ] POWER SOURCES -- Video monitor or equipment should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your video monitor or equipment dealer or local power company. For video monitor or equipment designed to operate from battery power refer to the operating instructions. 17. REPLACEMENT PARTS -- When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. 9. GROUNDING OR POLARIZATION -- This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 18. SAFETY CHECK -- Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition. 10. POWER CORDS -- Do not allow anything to rest on the power cord. TITLE : Lets you display the title name (8 characters) on the screen for each component which is connected to the terminals at the rear of the monitor. VERSION : This item is for display only and cannot be changed. Underscan/overscan select button (SCAN) for Model 8618 only The initial setting is for the normal screen (overscan). If the SCAN button is pressed, the screen will become smaller (underscan) than the normal screen. Change this setting in cases such as when screen display characters are missing. If the SCAN button is pressed once more, the normal screen is displayed again. 7 Monitor A selector button (A) When this button is pressed, the audio and video input changes to the component which is connected to the A terminals at the rear of the monitor. 8 Monitor B selector button (B) When this button is pressed, the audio and video input changes to the component which is connected to the B terminals at the rear of the monitor. 9 Monitor Y/C selector button (Y/C) When this button is pressed, the audio and video input changes to the component which is connected to the Y/C terminals at the rear of the monitor. F Power indicator (POWER) Lights when the power is on. G Power button (POWER) 4 Press this button to turn the power on and off. PARTS NAMES Rear Panel 2 3 4 1 1 AC INPUT socket Connect the AC power cord (supplied) securely to this socket and to a wall outlet. 2 Rear A terminals (AUDIO/VIDEO A terminals) When the monitor A selector button at the front of the monitor is pressed, the audio and video signals from the component which is connected to these terminals can be monitored. A AUDIO OUT/IN terminals B VIDEO OUT/IN terminals 3 Rear B terminals (AUDIO/VIDEO B terminals) When the monitor B selector button at the front of the monitor is pressed, the audio and video signals from the component which is connected to these terminals can be monitored. C AUDIO OUT/IN terminals D VIDEO OUT/IN terminals 4 Rear Y/C terminals (AUDIO/VIDEO Y/C terminals) When the monitor Y/C selector button at the front of the monitor is pressed, the audio and video signals from the component which is connected to these terminals can be monitored. E AUDIO OUT/IN terminals F S-VIDEO OUT/IN terminals Note: If there is no signal being input from the input terminals selected (A, B or Y/C) at the rear of the monitor, "NO SIGNAL" will be displayed. 5 CONNECTION Before making any connection, make sure all the devices are turned off. Before making the connections, please refer to the instruction manual accompanying each device. If the devices are not connected properly, that may cause a fire and/or damages. Basic connections Connections to the S-VIDEO terminals Monitor Video recorder To Video input terminal To Audio input terminal To AUDIO input terminal : IN signal : OUT signal To S-VIDEO input terminal To Video input terminal To Audio input terminal To AUDIO A INPUT terminal (Rear panel) To VIDEO A INPUT terminal To AUDIO B INPUT terminal To VIDEO B INPUT terminal To AUDIO input terminal To Y/C input terminal Video camera Monitor Video recorder Video camera Monitor Video recorder Note: · The components and connection cables are not included and must be purchased separately. · If connecting a single component, it can be connected to either the A or B terminals at the rear of the monitor. 6 BASIC OPERATION 1 Press the POWER button to turn on the power. ON: The power is turned on (the POWER indicator is lit). [. . . ] (See page 11. ) OSD OSD Monitor switching time (dwell time) setting For Model 8613 only 1 Select "7. DWELL TIME 5S" and then press the ENTER button. 2 Use the cursor (l) and (j) buttons to adjust the dwell time. · The time can be set to between 1 second and 31 seconds. OSD 3 Return to the menu screen display and then press the SEQUENCE button. [. . . ]