User manual SANYO TLS1960P

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or other moisture. CAUTION: Changes or modifications not expressly approved by the manufacturer may void the user's authority to operate this equipment. For the customers in Canada This class B digital apparatus complies with Canadian ICES-003. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generated, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] When the heads are dirty and the recording quality deteriorates, the output at the WARNING OUT terminal becomes 0V (Low), the "m" indicator flashes on the digital display, and the buzzer sounds. is set to "N", the recording quality is not monitored. 2 Press the * (or +) button, until the "TAPE END MODE" setting is flashing. 3 Press the l (or j) button to set the desired mode. X Setting when the REPEAT REC switch is set to the "OFF" position. Rewinds the tape to the beginning, then goes to stop mode STOP . The cassette is ejected X Setting when the REPEAT REC switch is set to the "ON" position. Autorepeat recording mode is automatically canceled if there was an alarm trigger R2. Autorepeat recording mode is active even if there was an alarm trigger NOTES: X To cancel the "m" indicator display and reset the WARNING OUT terminal output, press the STOP button. X Clog detection is not possible if recording in 2-hour mode. 4 Press the SEARCH/AUDIO ON button to save the setting. 18 English AUTOREPEAT RECORDING Autorepeat Recording The same tape can be recorded over many times. X Follow the Before starting steps, under "NORMAL RECORDING". NOTES: X If during autorepeat recording there is an alarm trigger, "AL" is displayed on the digital display and alarm recording will take place. (Please refer to page 20, "ALARM RECORDING". ) X If the "TAPE END MODE" setting is R 1, the REPEAT indicator will go off if there is an alarm trigger. After alarm recording, the recording will continue to the end of the tape then it will be rewound to the beginning and stop. "OFF" will be displayed on the digital display. If the alarms are going to be reviewed using alarm scan or alarm search, then in 2-hour mode, 20-second or more recording duration should be used. 2 3 Press the MENU button until the (SET UP 3) menu is displayed. @Y 4 Press the l (or j) button to set the desired alarm mode. Y1. Alarm recording is done when there is an alarm trigger. Alarm recording is done only when there is an alarm trigger during programmed timer recording. Alarm recording is done only if there is an alarm trigger and the VCR is not in programmed timer recording mode. Alarm recording is done only when there is an alarm trigger during programmed timer recording duration. Alarm recording is not performed even if there is an alarm trigger. 20 English ALARM RECORDING Alarm Recording Counter Display X During alarm recording, "AL" will be flashing on the digital display. X If the ON SCREEN switch is set to the "ON" position, the number of alarms will flash on the monitor screen. X The maximum display number of alarm recordings is "999", at the next alarm recording the counter will indicate "000". X When the (ALARM TIME) menu is displayed, press the MENU RESET button to reset the alarm counter to "000" (all the data of the (ALARM TIME) menu is reset). Checking the Alarm Recordings Time 1 Press the MENU button until the (ALARM TIME) menu is displayed. ø The number of alarm recordings, and the 8 most recent alarm recording times are displayed. [. . . ] After this, repeat from the start or the table. For places with symbols such as E (k) and F (k), carry out checking and cleaning, and replace if necessary. This periodic maintenance check table changes considerably according to the using conditions and environment. Refer to (USED TIME) menu for the length of time the unit has been used. [. . . ]