User manual SANYO TLS9924P

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or other moisture. CAUTION: Changes or modifications not expressly approved by the manufacturer may void the user's authority to operate this equipment. For the customers in Canada This class B digital apparatus complies with Canadian ICES-003. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] 19200 4 Turn the SHUTTLE ring to set the desired alarm mode. Alarm recording is done when there is an alarm trigger. Alarm recording is done only when there is an alarm trigger during programmed timer recording. Alarm recording is done only if there is an alarm trigger and the VCR is not in programmed timer recording mode. Alarm recording is done only when there is an alarm trigger during programmed timer recording duration. Alarm recording is not performed even if there is an alarm trigger. 20 English ALARM RECORDING Alarm Recording Counter Display oe During alarm recording, "AL" will be flashing on the digital display. oe If the ON SCREEN switch is set to the "ON" position, the number of alarms will flash on the monitor screen. oe The maximum display number of alarm recordings is "999", at the next alarm recording the counter will indicate "000". oe When the (ALARM TIME) menu is displayed, press the MENU RESET button to reset the alarm counter to "000" (all the data of the (ALARM TIME) menu is reset). Checking the Alarm Recordings Time 1 Press the MENU button until the (ALARM TIME) menu is displayed. ø The number of alarm recordings, and the 8 most recent alarm recording times are displayed. 09-25@10:52 Connections to the ALARM IN/OUT Terminals oe Alarm input signal Connect a make-contact (no voltage) switch between the ALARM IN and COM terminals. ø The recording stop hour position starts flashing. Example 2: To record every week from Saturday at 9:00 PM (21:00) to Monday at 7:00 AM, in 48-hour mode (recording speed). oe Follow the Before starting steps, under "NORMAL RECORDING". 9 Turn the SHUTTLE ring to set the recording stop hour (ex: 07), then turn the JOG dial clockwise. ø The recording stop minutes position starts flashing. 1 Press the MENU button until the (TIMER SET) menu is displayed. oe "SUN" (Sunday) will be flashing. F Turn the SHUTTLE ring to set the recording stop minutes (ex: 00), then turn the JOG dial clockwise. ø The "SPD" (recording speed) position will start flashing. 2 Turn the JOG dial, until "SAT" is flashing. 3 Turn the SHUTTLE ring to set the desired start day of the week (ex: SAT), then turn the JOG dial clockwise. ø The recording start hour position starts flashing. G Turn the SHUTTLE ring to select the recording speed mode (ex: 48), then turn the JOG dial clockwise. ø "N" will start flashing. H Turn the SHUTTLE ring to select "Y". ---@N 4 Turn the SHUTTLE ring to set the recording start hour (ex: 21), then turn the JOG dial clockwise. ø The recording start minutes position starts flashing. 5 Turn the SHUTTLE ring to set the recording start minutes (ex: 00), then turn the JOG dial clockwise. ø The recording stop hour position starts flashing. I Follow steps F and G under "PROGRAM TIMER RECORDING" on page 23. 6 Turn the SHUTTLE ring to set "öö" for the recording stop hour. [. . . ] After this, repeat from the start or the table. For places with symbols such as E (k) and F (k), carry out checking and cleaning, and replace if necessary. This periodic maintenance check table changes considerably according to the using conditions and environment. Refer to (USED TIME) menu for the length of time the unit has been used. [. . . ]