User manual SANYO VCB-3444

[. . . ] SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 4 7 9 10 13 14 15 · Low smear, anti-blooming, low lag, no burning and no geometric distortion using the CCD solid state image device. · 100% solid state components giving excellent immunity to shock and vibration · Not subject to interference from magnetic or electrostatic fields · High sensitivity, minimum required illumination of 0. 05 lux with F1. 2 lens · Horizontal resolution, more than 400 TV lines · Backlight compensation function (Active when using an auto-iris lens) · Externally adjustable flange back (mechanical focus) · Low power consumption and quick start · Power supply: 24 V AC operation English 1 INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] In such a case, adjust the LEVEL volume on the lens casing to correct. 6 English MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length "L" is more than 9 mm. If not, that may damage the camera and prevent proper installation. L 1 2 1 Remove the lens mount cap from the camera. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. C mount type lens To allow for flange-back adjustment, install the C-mount adaptor (option) on the lens mount, then carefully align the lens mount with the camera opening and turn the lens slowly to install it. Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. When using lenses from other makers, the plug shape may not correspond to the terminal on the camera. In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug according to the diagram. (Refer to page 8. ) C mount type lens 2 3 3 2 CS mount type lens English 7 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 1 2 2 Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. Pin layout 2 4 1 3 2 4 1 3 1 2 3 4 DC type lenses Brake coil (­) Brake coil (+) Drive coil (+) Drive coil (­) VIDEO type lenses +10 V DC (50 mA max. ) Not used Video output (1. 0 Vp-p, high impedance) Ground (for video signal and DC power) Flange-back adjustment 1 If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 1 2 1, 3 2 3 4 5 Before installing the lens, check that the two flange-back lock screws have been tightened. If the flange-back lock screws are loose, the CS mount ring will not be secured and it will not be possible to adjust the flange-back. Fully install the lens, then loosen the two flange-back lock screws. Set the zoom lens to the maximum telephoto position (TELE), then set the focus using the focus ring on the lens. Set the zoom lens to the maximum wide angle position (WIDE), then set the focus by turning the CS mount ring. Repeat steps 3 and 4 until the image stays in focus when changing from a telephoto shot to a wide angle shot. When the setting is complete, tighten the two flange-back lock screws. 8 English CONNECTIONS 3 1 (A) 2 (Video signal connections) : VIDEO IN : VIDEO OUT Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc. ) and cables are sold separately. 3 1 2 Make the video signal connection between the camera and the monitor or time lapse VCR. Connect to 24 V AC UL listed class 2 power supply (sold separately). Insert the plug of this power cord into a wall outlet. Adjust the picture on the monitor using the Brightness and Contrast controls. Coaxial cable type and maximum length CAUTION: · To prevent camera and/or power supply failure, pay close attention to polarity when making the connections. · Cable type RG-59U (3C-2V), 250 m maximum. [. . . ] This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance. This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair. This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear. The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability. [. . . ]