User manual SANYO VCB-3524

[. . . ] The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability. THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. [. . . ] Changes or modifications not expressly approved by Sanyo may void the user's authority to operate this camera. ENGLISH 2 English PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer (or a Sanyo Authorized Service Centre). Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera. If used with a foreign object inside, it could cause a fire, short-circuits or damages. If water or a liquid gets inside the camera, disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Be careful to protect the camera from rain, sea water, etc. Be careful when handling the unit To prevent damages, do not drop the camera or subject it to strong shock or vibration. Install away from electric or magnetic fields If installed close to a TV, radio transmitter, magnet, electric motor, transformer, audio speakers the magnetic field they generate will distort the image. Protect from humidity and dust To prevent damages to the camera, do not install it where there is greasy smoke or steam, where the dampness may get too high, or where there is a lot of dust. When the setting is complete, tighten the FLANGE BACK LOCK screw. MOUNTING THE LENS Check the lens mount Do not use a lens if the length "L" is more than 7 mm. That may damage the camera and prevent proper installation. L Installation of a DC type auto-iris lens (sold separately) A 1/3 inch CS mount type lens without EE amplifier circuit that only uses a DC power source. LENS switch to the DC type) a CS mount type lens without the need of an adaptor. If the lens plug shape or wiring does not correspond, please install the supplied plug as indicated in the pin layout table. 6 English MOUNTING THE LENS 2 (A) (B) Installation of a VIDEO type auto-iris lens (sold separately) A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit that uses the video signal and a DC power source. 1 2 3 1 2 4 3 Remove the lens mount cap. Attach the supplied C mount adaptor (A) to the auto-iris lens (B), then install the assembly on the camera. Connect the lens plug to the LENS connector on the side of the camera. If the lens plug shape or wiring does not correspond to the specifications below, connect the supplied plug as indicated. · Cable type RG-39U, 200 m maximum. CAUTION: The RG-59U type cable should not be run through electrical conduits or through the air. (Video signal connections) : VIDEO IN : VIDEO OUT English 9 SETTINGS VR401 L EI ON OFF ON E V E L HL DC VIDEO BLC A. LENS Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the EI/BLC switch to EI-ON position. EI ON OFF ON Note: Please refer to the specifications for dynamic range of the electronic iris. BLC CAUTION: · The electronic iris is suitable for normal indoor use. When the EI/BLC switch is set to the EI-ON position, do not use an auto-iris lens. [. . . ] Are all the signal connecting cables correctly connected?Is the lens type (DC or VIDEO) correctly selected?· Is the iris control correctly set?A: When using a DC type lens, the LEVEL volume (inside the camera casing) should be adjusted. [. . . ]