User manual SANYO VCC-3912

[. . . ] INSTRUCTION MANUAL COLOR CCD Camera VCC-3912 SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC's warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-800-421-5013. New Jersey Office 210 Riser Road Little Ferry, NJ 07643 201-641-3000 California Office 1200 W. Compton, CA 90220 310-537-5830 Illinois Office 900 N. [. . . ] Protect from high temperatures Do not install close to stoves, or other heat generating devices, such as spotlights, etc. , or where it could be subject to direct sunlight, as that could cause deformation, discoloration or other damages. Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels. Install where the temperature range will stay between ­10°C and 50°C. (no condensation) Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. 4 English PREPARATION 1 2 32 2 1 B A Camera installation A: Lens mount cap Remove the lens mount cap before installing the lens (sold separately). · Use with this camera a CS mount type auto-iris lens (for 1/3 inch). Auto-iris lenses regulate the amount of light entering the camera according to the brightness of the subject. · C mount auto-iris lenses can also be used with the supplied adaptor (see page 7). R1 R2 CAUTION: · When installing the camera support, select a location that can support the total weight of the camera and accessories. · This installation should be made by a qualified service person and should conform to all local codes. B: Installation bracket The bracket can be fitted at the top or bottom of the camera. To fix the bracket, make sure to use the screws that held the bracket before, and use the other two screws to seal the openings on the opposite side. 1 Opening sealing screws (M3x4) (shorter) 2 Bracket fixing screws (M3x6) (longer) 3 Threaded hole for the support (1/4"­20 UNC) · Mounting at the top (R1) · Mounting at the bottom (R2) English 5 (A) 1 L 4 DC VIDEO 3 2 Installation of a DC type lens (sold separately) 1/3 inch CS mount type (Flange-back: 12. 5 mm) LENS connector layout (A) 1: Brake coil (­) 2: Brake coil (+) 3: Drive coil (+) 4: Drive coil (­) 1 2 Remove the lens mount cap. Install the auto-iris lens onto the camera. In such a case, adjust the LEVEL volume on the lens casing to correct. Compatible auto-iris lens · f= 9 mm (Standard angle) · f= 12 mm (Telephoto) · f= 16 mm (More telephoto) English 7 CONNECTIONS 1 4 (A) 2 (Video signal connections) : VIDEO IN : VIDEO OUT Basic connection for monitoring or recording The peripheral devices (VCR, monitor, etc. ) and cables are sold separately. Coaxial cable type and maximum length · Cable type RG-59U, 100 m maximum. · Cable type RG-39U, 200 m maximum. 1 2 3 4 Make the video signal connection between the camera and the monitor or time lapse VCR. Connect DC connecting cord from the AC adaptor to the 12V DC IN terminal on the camera. Turn on the power of all the devices connected to the camera. When the power is connected to the camera, the POWER indicator (A) will light. [. . . ] This sets the electronic shutter speed to 1/60 sec. The switches can be set as indicated in table B to select one of the 8 speeds available. ON ON ON CAUTION: · The high speed electronic shutter function cannot be used together with the electronic iris function. When using the high speed electronic shutter, the EI/BLC switch must be set to the OFF position. · Using the high speed electronic shutter indoors with low lighting, will give darker pictures. [. . . ]