User manual SANYO VCC-3924

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. [. . . ] Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels. Install where the temperature range will stay between ­10°C and 50°C. (no condensation) s Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. English 3 PARTS NAMES 2 1 Flange-back lock screw (LOCK) 2 Flange-back adjustment dial 3 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 4 Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings. 1 3 4 CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. 1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw hole: 1/4"-20 UNC 4 English PARTS NAMES 9 5 6 7 8 9 Camera setup section White balance adjustment volume (WB R or B) Line phase adjustment volume (PHASE) Lens iris adjustment volume (LEVEL) Lens iris output connector (LENS) 5 6 7 8 This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. F Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. Switch 2 should normally be set to "NORM". If the monitoring location is dark and you would like to increase the luminance (brightness), set switch 2 to "HI". Note: If switch 2 is set to "HI", the images from the monitoring location will become brighter, but interference may become more noticeable. CAUTION: · The electronic iris is suitable for normal indoor use. When the switch 1 is set to the up (EI) position, do not use an auto-iris lens. · If used under fluorescent light, the image may flicker. In such a case, change to incandescent lighting or set the switch 1 to the down (AI) position and use an auto-iris lens. · When shooting bright subjects, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect. HI NORM 10 English SETTINGS s Backlight compensation setting 3 4 This camera has two different backlight correction functions: multi-spot photometry (MULTI) and center focus photometry (CENT). The normal setting (switch 3 and 4) is the down position, but you can change the switch 3 or 4 setting in accordance with the backlight conditions. (MULTI mode: 64 sections) MULTI CENT 3 4 · MULTI mode: Use this position when applying backlight compensation to the whole of the screen. · CENT mode: Use this position when applying backlight compensation to only the central portion of the screen. Note: · When using the backlight compensation function, set the switch 3 or 4 to the up position. [. . . ] THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED. Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail. LABOR 3 YEARS PARTS 3 YEARS IMAGE DEVICE 3 YEARS EXCLUSIONS This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model's instruction manual, or (B) the repair of any product whose serial number has been altered, defaced or removed. [. . . ]