User manual SANYO VCC-3944

[. . . ] 9 TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 English 1 INFORMATIN TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] G 24 V AC or 12 V DC input terminal (AC24V, DC12V, GND) H Power indicator (POWER) Comes on when the power to the camera is on. F G H s Power supply connections Use a 3 wire grounded cable (18 AWG or more), and connect as shown by the illustration. CAUTION: · To prevent camera and/or AC adaptor failure, pay close attention to polarity when making the connections. · To prevent fire hazard any UL listed wire rated VW-1, should be used for the 24 V AC cable input terminal. English 5 MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). 1 Check the lens mount Do not use a lens if the length "L" is more than 5 mm. That may damage the camera and prevent proper installation. C mount type lens L 2 1 2 Remove the lens mount cap from the camera. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. C mount type lens To allow for flange-back adjustment, install the C-mount adaptor (option) on the lens mount, then carefully align the lens mount with the camera opening and turn the lens slowly to install it. Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. 3 2 CS mount type lens 3 6 English MOUNTING THE LENS s Pin layout 2 4 1 3 1 2 3 4 DC type lenses Brake coil (­) Brake coil (+) Drive coil (+) Drive coil (­) 3 s Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 2 1 1 2 3 4 Using a + screwdriver, loosen the flange-back lock screw (M2:+). Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens. Set the zoom lens to the maximum wide angle position, set the focus using the flange-back adjustment dial. Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot. When the setting is complete, tighten the flange-back lock screw. English 7 CONNECTIONS 1 (A) 24 V AC connection GND AC24V 12 V DC connection GND AC24V DC12V DC12V Figure 1 Figure 2 (Video signal connections) : VIDEO IN : VIDEO OUT Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc. ), AC adaptor and cables are sold separately. 3 1 2 Make the video signal connection between the camera and the monitor or time lapse VCR. · If using a commercially-available 24 V AC adapter, always be sure to connect the ground wire (18AWG or higher) to the ground terminal. (Figure 1) · If using a 12 V DC power supply, make the connections as shown in Figure 2. Note: · In order to avoid any problems with the camera and the power supply, take sufficient care to ensure that the polarities are correct when connecting the power supply. Insert the plug of this power cord into a wall outlet. Adjust the picture on the monitor using the Brightness and Contrast controls etc. s Coaxial cable type and maximum length · Cable type RG-59U (3C-2V), 250 m maximum. · Cable type RG-6U (5C-2V), 500 m maximum. · Cable type RG-11U (7C-2V), 600 m maximum. CAUTION: · The RG-59U type cable should not be run through electrical conduits or through the air. · Use CCTV/Video-grade coaxial cable. 8 English SETTINGS s Camera setup section No. Settings Electronic Iris (EI)/Auto iris (AI) setting Gain up setting · HI (High)/NORM (Normal) Backlight compensation mode setting (BLC) · MULTI (Multi)/OFF Backlight compensation mode setting (BLC) · CENT (Center)/OFF White balance setting · MANU (manual)/ATW (auto tracing white balance) Syncronisation (SYNC) setting · LL (Line lock)/INT (Internal sync) Lens iris adjustment (LEVEL) Position AI NORM OFF OFF ATW INT -- 1 2 3 7 4 5 123456 6 7 English 9 SETTINGS s Iris function setting 1 This should normally be set to the down (AI) position. Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the switch 1 to the up (EI) position. When using an auto-iris lens (for indoor/ outdoor use) Set the switch 1 to the down (AI) position. CAUTION: If conditions are outside the electronic iris operation range or more than the maximum illumination, it will cause saturation of the CCD. In that case, use a manual iris lens. EI AI s Gain up setting 2 Note: Please refer to the specifications for dynamic range of the electronic iris. [. . . ] This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance. This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair. This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear. The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability. [. . . ]