User manual SANYO VCC-4324

[. . . ] INSTRUCTION MANUAL COLOR CCD CAMERA VCC-4324 About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC's warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-800-421-5013. New Jersey Office 210 Riser Road Little Ferry, NJ 07643 201-641-3000 California Office 1200 W. Compton, CA 90220 310-537-5830 Illinois Office 900 N. [. . . ] Protect from humidity and dust To prevent damages to the camera, do not install it where there is greasy smoke or steam, where the dampness may get too high, or where there is a lot of dust. Protect from high temperatures Do not install close to stoves, or other heat generating devices, such as spotlights, etc. , or where it could be subject to direct sunlight, as that could cause deformation, discoloration or other damages. Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels. Install where the temperature range will stay between ­10°C and 50°C. (no condensation) Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. English 3 PARTS NAMES 1 1 3 1 Lens iris output connector (4 pin) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. 2 Flange-back adjustment lever (See page 7) 2 4 2 3 Flange-back lock screw 4 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 3 4 5 5 Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings. 1 2 32 CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. 1 1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw hole: 1/4"-20 UNC 4 English PARTS NAMES 6 Camera setup section (under the cover) This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover. Control name Position L INT about center A OFF DC about center 6 ab C-BW de f g WB EI A ON OFF ON VR301 a Color and Black/White level switch (C-BW) b Internal/Line lock switch (SYNC) c Red and Blue color adjustment volume (R, B) d e f g White balance switch (WB) Electronic iris (EI)/Backlight compensation (BLC) switch Auto-iris lens switch (A. I. LENS) Lens iris level volume (LEVEL) L-L H L INT SYNC R VR303 VR302 LEVEL L H M B BLC DC VIDEO A. LENS c Notes: · The EI/BLC switch cannot be used simultaneously. · When using a 1/2 or 2/3 inch C mount VIDEO (with EE internal amplifier) auto-iris type lens, set the A. I. LENS switch to the DC type) a CS mount type lens without the need of an adaptor. If the lens plug shape or wiring does not correspond, please install the supplied plug as indicated in the pin layout table. 2 (A) (B) Installation of a VIDEO type auto-iris lens (sold separately) A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit that uses the video signal and a DC power source. 1 2 3 3 1 2 4 3 Remove the lens mount cap. Attach the supplied C mount adaptor (A) to the auto-iris lens (B), then install the assembly on the camera. Connect the lens plug to the LENS connector on the side of the camera. [. . . ] When the EI/BLC switch is set to the EI-ON position, do not use an auto-iris lens. · If used under fluorescent light, the image may flicker. In such a case, change to incandescent lighting or set the EI/BLC switch to the OFF position and use an auto-iris lens. · When shooting bright subjects, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect. English 13 SETTINGS C · B/W (color/black and white) switch setting This switch lets you select the timing of the automatic switching of the optical filter to color image or black and white image, according to the subject brightness. [. . . ]