User manual SANYO VCC-4374

[. . . ] INSTRUCTION MANUAL COLOR CCD CAMERA VCC-4374 About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below. For product operation, authorized service center referral, service assistance or problem resolution, call CUSTOMER INFORMATION 1-800-421-5013 Weekdays 8:30 AM ­ 5:00 PM Pacific Time For accessories and/or parts, call PARTS ORDER INFORMATION 1-800-726-9662 Weekdays 8:30 AM ­ 5:00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL U. S. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER. [. . . ] To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. English 3 PARTS NAMES 1 Power indicator (POWER) Comes on when the power to the camera is on. 4 1 2 GC B 2 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 3 Manual color/black and white setting terminal (CONTROL) 5 · G (ground) terminal · C (color) terminal · B (black and white) terminal 3 4 Line phase adjustment volume (LINE PHASE) When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this volume. 5 24 V AC input terminal (24 V AC, GND) 6 Camera setup section (under the cover) 6 7 These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, loosen the cover fixing screw A, then remove the cover. 7 Lens iris output connector (LENS) A This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. 4 English PARTS NAMES 8 Flange-back lock screw F 8 9 G 9 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). F Flange-back adjustment lever (See page 7) 1 2 32 G Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings. 1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw hole: 1/4"-20 UNC 1 CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. English 5 CONCERNING AUTO-IRIS LENSES DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. Checking the lens mount Do not use a lens if length "L" is more than 5 mm. If not, that may damage the camera and prevent proper installation. L 1 1 2 Remove the lens mount cap from the camera. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. C mount type lens To allow for flange-back adjustment, install the supplied C-mount adaptor on the lens mount, then carefully align the lens mount with the camera opening and turn the lens slowly to install it. Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. When using lenses from other makers, the plug shape may not correspond to the terminal on the camera. In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug according to the diagram. (Refer to page 9. ) C mount type lens 2 3 3 2 CS mount type lens 8 English MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 1 2 2 Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. Pin layout 2 4 1 3 2 4 1 3 1 2 3 4 DC type lenses Brake coil (­) Brake coil (+) Drive coil (+) Drive coil (­) VIDEO type lenses +12 V DC (50 mA max. ) Not used Video output (1. 0 Vp-p, high impedance) Ground (for video signal and DC power) English 9 CONNECTIONS (A) 1 Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc. ) and cables are sold separately. 1 2 2 Make the video signal connection between the camera and the monitor or time lapse VCR. Connect to 24 V AC UL listed class 2 power supply. CAUTION: · To prevent camera and/or power supply failure, pay close attention to polarity when making the connections. · To prevent fire hazard any UL listed wire rated VW-1, should be used for the 24 V AC cable input terminal. 3 Insert the plug of this power cord into a wall outlet. Adjust the picture on the monitor using the Brightness and Contrast controls. [. . . ] CONTROL terminal Image Auto Black and white color Auto GCB (Fig. 2) H: for a brighter setting than L L: Standard setting Notes: C H H L L B H L H L · After the power has been turned off, switching will restart from color, when the power is restored. · A sound may be heard when the color image or black and white image is switched. Also, the image will be distorted as shown in Fig. 2, this is normal and does not indicate a problem. [. . . ]