User manual SANYO VCC-5774

[. . . ] This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear. The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability. SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. [. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Sanyo may void the user's authority to operate this camera. 4 English PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Be careful when handling the unit To prevent damages, do not drop the camera or subject it to strong shock or vibration. Install away from electric or magnetic fields If installed close to a TV, radio transmitter, magnet, electric motor, transformer, audio speakers the magnetic field they generate will distort the image. Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer (or a Sanyo Authorized Service Centre). Protect from humidity and dust To prevent damages to the camera, do not install it where there is greasy smoke or steam, where the dampness may get too high, or where there is a lot of dust. Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera. If used with a foreign object inside, it could cause a fire, short-circuits or damages. If water or a liquid gets inside the camera, disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Be careful to protect the camera from rain, sea water, etc. English 5 PRECAUTIONS Protect from high temperatures Do not install close to stoves, or other heat generating devices, such as spotlights, etc. , or where it could be subject to direct sunlight, as that could cause deformation, discoloration or other damages. Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels. Install where the temperature range will stay between ­10°C and 50°C. (no condensation) Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. 6 English PARTS NAMES 1 Camera mounting screw hole 2 3 CAUTION: When installing the camera, select a location that can support the total weight of the camera and accessories. 1 4 2 Electronic iris function switch (EI OFF/EI ON) 3 Sync switch (INT/L-L) INT (Internal sync) position L-L (Line lock) position 4 Line phase adjustment volume (LINE PHASE) 5 Lens iris level volume (LEVEL) 6 Lens iris output connector (LENS) 5 1 6 1 3 This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. 2 4 English 7 PARTS NAMES 8 7 Flange-back lock screw 8 CS mount ring 9 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens. 7 9 7 F Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. G 24 V AC or 12 V DC input terminal (24 V AC, 12 V DC, GND) . . . See page 11 G F 8 English MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount L Do not use lense with a length L more than 5 mm. If not, that may damage the camera and prevent proper installation. 1 1 2 Remove the lens mount cap from the camera. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. C mount type lens 2 C mount type lens Install the supplied C-mount adaptor on the lens mount, then carefully align the lens mount with the camera opening and turn the lens slowly to install it. 3 3 English 9 Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. The plug shape may not correspond to the terminal on the camera. In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug according to the diagram. (Refer to page 10. ) 2 CS mount type lens MOUNTING THE LENS 1 Rewiring the lens cable in the lens iris plug 1 2 Prepare the lens cable. Cut the cable at the plug, then remove approx. If that is the case, adjust the flange-back position as described below. 1 Flange-back lock screw Before installing the lens, check that the two flange-back lock screws have been tightened. [. . . ] If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens cleaning set. SERVICE This camera is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre. English 17 SPECIFICATIONS Scanning system: NTSC standard TV system (525 TV lines, 30 frames/sec. ) Interlace: 2:1 interlace Image device: 1/3 inch solid state image device CCD Picture elements: 816 (H) x 494 (V) Effective picture elements: 771 (H) x 492 (V) Synchronizing system: Manual internal sync/ Line lock switching Resolution: 480 TV lines horizontally, 350 TV lines vertically Video output level: 1. 0 Vp-p/75 ohms, composite Video S/N ratio: More than 48 dB Minimum required illumination (incandescent lighting): AGC ON: Approx. [. . . ]