User manual SANYO VCC-5974

[. . . ] INSTRUCTION MANUAL COLOR CCD Camera VCC-5974 About this manual · Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC's warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-800-421-5013. New Jersey Office 210 Riser Road Little Ferry, NJ 07643 201-641-3000 California Office 1200 W. [. . . ] To switch between menus and selection When the setting of a switch in the camera setup section is changed, the corresponding sub-menu is displayed. To adjust the values or settings, press the CURSOR (d or c) button to select the desired value or setting, then press the SET button. Initial values protection (WRITE PROTECT) ON: Default setting. OFF: Press the CURSOR (d or c) button to select OFF, then press the SET button. The write protection is cancelled and the initial values can then be changed. To exit the menu Press the CURSOR (j or l) button to select END (get it flashing), then press the SET button. To switch to the second page of the "MENU FOR ADJUSTMENT" Press the CURSOR (j or l) button to select NEXT PAGE (get it flashing), then press the SET button. To switch back to the first page of the "MENU FOR ADJUSTMENT" Press the CURSOR (j or l) button to select PREVIOUS PAGE (get it flashing), then press the SET button. To enter a camera ID (CAMERA ID) (See page 24). Aperture display (APERTURE) (See page 25). SET INT CURSOR SET 3 CURSOR CURSOR SET 4 5 6 7 8 CURSOR SET (or j) English 13 ADJUSTMENTS To enter settings or adjustments for the camera it must be connected to a monitor. The settings and adjustments are made by ways of on-screen displays. Concerning the WRITE PROTECT function In order to protect the settings and adjustments the WRITE PROTECT function is set to ON. If it is necessary to enter new settings or adjustments, press the CURSOR (j or l) button to select the WRITE PROTECT function setting, then press the CURSOR (d or c) button to select OFF, then press the SET button. CURSOR CURSOR SET (Menu 1) MENU FOR ADJUSTMENT SYNC IRIS BLC WHITE BALANCE AGC SHUTTER WRITE PROTECT NEXT PAGE INT AI ON ATW ON 60 OFF END CONTENTS OF ADJUSTMENTS 1. V sync phase adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1-2. VBS phase adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2. Auto-iris level adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3. Setting the light measuring area characteristics (size, position and distribution) for the MANUAL 1 setting. . . . . BLC level adjustment for the PRESET 1 setting . . . . . . . . . . . . . 20 4. PRESET MODE 2 (indoors, fluorescent lighting) setting adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MANUAL setting adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5. AGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 6. CAMERA ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7. [. . . ] The second page of the "MENU FOR ADJUSTMENT" will be displayed. CURSOR SET SHUTTER WRITE PROTECT NEXT PAGE 60 OFF END MENU FOR ADJUSTMENT CAMERA ID APERTURE ON 2 3 Press the CURSOR (j or l) button to select APERTURE (get it flashing), then press the SET button. The adjustment sub-menu "ADJUSTMENT FOR APERTURE" will be displayed. Press the CURSOR (d or c) button to adjust the aperture setting (0 to 15 range). The on-screen marker (b) will move and the adjustment value will flash according to the aperture setting. [. . . ]