User manual SANYO VCC-6574

[. . . ] INSTRUCTION MANUAL COLOR CCD CAMERA VCC-6574 About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below. For product operation, authorized service center referral, service assistance or problem resolution, call CUSTOMER INFORMATION 1-800-421-5013 Weekdays 8:30 AM ­ 5:00 PM Pacific Time For accessories and/or parts, call PARTS ORDER INFORMATION 1-800-726-9662 Weekdays 8:30 AM ­ 5:00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL U. S. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER. [. . . ] (no condensation) Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. English 3 PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Line phase adjustment volume (LINE PHASE) 1 3 4 2 When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this volume. 3 Power indicator (POWER) Comes on when the power to the camera is on. 4 24 V AC input terminal (AC 24 V, GND) Power supply connections Use a 3 wire grounded cable (22 AWG or more), and connect as shown by the illustration. CAUTION: · To prevent camera and/or AC adaptor failure, pay close attention to polarity when making the connections. · To prevent fire hazard any UL listed wire rated VW-1, should be used for the 24 V AC cable input terminal. 4 English PARTS NAMES 5 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 5 8 7 6 6 Flange-back adjustment screw (FLANGE BACK ADJ. ) 7 Flange-back lock screw (FLANGE BACK LOCK) 8 Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings. 1 2 32 CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. 1 1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw hole: 1/4"-20 UNC English 5 PARTS NAMES 9 Lens iris output connector (LENS) F 9 This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. F Camera setup section (under the cover) These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover. Notes: · When using a 1/2 or 2/3 inch C mount VIDEO (with EE internal amplifier) auto-iris type lens, set the A. I. In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug according to the diagram. (Refer to page 9. ) 3 8 English MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 1 2 Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. 2 Pin layout 2 4 1 3 2 4 1 3 1 2 3 4 DC type lenses Brake coil (­) Brake coil (+) Drive coil (+) Drive coil (­) VIDEO type lenses +12 V DC (50 mA max. ) Not used Video output (1. 0 Vp-p, high impedance) Ground (for video signal and DC power) Flange-back adjustment 2, 3 If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 3 ADJ. 1 LOCK 4 1 2 3 4 Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+). Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens. Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ. Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot. When the setting is complete, tighten the FLANGE BACK LOCK screw. English 9 CONNECTIONS 1 (A) 2 AC 24 V AC 24 V connection Push to insert the cable (Video signal connections) : VIDEO IN : VIDEO OUT ~ ~ GND Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc. ), AC adaptor and cables are sold separately. CAUTION: · The RG-59U type cable should not be run through electrical conduits or through the air. 1 2 Make the video signal connection between the camera and the monitor or time lapse VCR. Insert the plug of this power cord into a wall outlet. [. . . ] If a manual white balance adjustment is necessary, follow the steps below. Set the switch 5 (WB) to the up (MANU) position, then adjust the color. · Turn R (VR302) to set the red ratio and/or B (VR303) to set the blue ratio. Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. 1 2 Set the switch 6 (SYNC) to the up (LL) position. [. . . ]