User manual SANYO VCC-6584E

[. . . ] Be sure to keep it handy for later reference. Pour la clientèle canadienne Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada. This installation should be made by a qualified service person and should conform to all local codes. Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the unit. If used with a foreign object inside, it could cause a fire, a short-circuit or damage. Be careful to protect the unit from rain, sea water, etc. [. . . ] Depending on the type of lens, the shape of the lens plug may differ. In this case, consult your dealer or an Authorized Sanyo Service Center. When attaching a C mount lens, attach the lens to the camera after inserting the C mount ring (sold separately). If the image is unclear L GND, AC24V, DC12V (ground terminal, AC 24 V or DC 12 V input terminal) VIDEO OUT (video output terminal: BNC connector) Connects to the video input terminal on the monitor, digital video recorder or time-lapse VCR. POWER (power indicator) Lights when the camera power is on. Camera adjustment/setting section See "CAMERA ADJUSTMENTS/SETTINGS". LENS (lens iris output terminal) Used to connect the lens plug when the auto-iris lens is attached. Brake coil (-) Brake coil (+) Drive coil (+) Drive coil (-) 1 Remove the lens mount cap from the camera. Is the monitor adjusted correctly?Is the flange-back position correctly set?Dirt or fingerprints on the lens can adversely affect the image. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available). 2 Install the auto-iris lens. 3 Connect the lens plug to the LENS terminal on the side of the camera. 1 SERVICE The camera is a precision instrument. Handle it carefully and always follow the safety precautions. If the camera requires service, never try to repair it yourself or open the casing. For servicing, maintenance, or repairs, consult your dealer or an Authorized Sanyo Service Center. Resolution Video output level Image S/N ratio Minimum required illumination (incandescent lighting) Backlight : OFF/Multi-spot metering (2 modes)/Centerweighted metering compensation Iris function : Auto-iris/Electronic-iris Lens iris output : 4-pin terminal Flange-back : 12. 5 mm ±0. 5 mm White balance : Auto/Manual Gain control : Normal/High Lens mount : CS mount Operating : Temperature: -10°C ­ +50°C (14°F ­ 122°F) environment Humidity: less than 90%RH (no condensation) Power supply : AC 24 V ±10%, 60 Hz/DC 12 ­ 15 V ±10% Power consumption : 3. 6 W (with auto-iris lens) Weight : Approx. 280 g (without lens) 3 CS mount type lens 2 Appearance and specifications are subject to change without prior notice or obligations. e_l5ax4_us_7. fm Page 2 Friday, April 23, 2004 2:13 PM CONNECTIONS AND INSTALLATION CONNECTIONS Monitor AC 24 V connection GND AC24V ADJUSTMENTS AND SETTINGS DC 12 V connection NOTE on EI setting: If fluorescent lighting is used where the camera is installed, the object will flicker as a result. This type of phenomenon can be avoided by replacing the fluorescent lighting with incandescent lamps. If the light entering the lens exceeds the maximum required illumination, the image cannot be displayed properly. In that case, manually adjust the lens iris. WB: White balance (color compensation) 5 R B 55 Lets you fine-tune the white balance manually. MANU ATW WB · R (Red) dial R : Turn clockwise to augment screen red. · B (Blue) dial B : Turn clockwise to augment screen blue. 3 GND AC24V 1 VIDEO OUT POWER 3 DC12V DC12V Compensation is performed automatically. 2 Figure 1 Figure 2 2 Gain control 2 For adjusting the sensitivity of the camera. Use this setting for shooting in dark environments. HI NORM Increased sensitivity allows shots to be taken in dark environments. Normal setting Sync setting 6 7 (Only when using an AC 24 V adapter) Line-Lock: Synchronizes the unit with power frequency when two or more cameras are connected via a switcher unit. [. . . ] SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SFC'S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN CONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR'S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT. 4 Repeat steps 2 and 3 if the image does 5 When the setting is complete, tighten 3 Insert the power adapter plug into the wall outlet. The camera comes pre-adjusted and ready to install at time of factory shipment, but you may want to make adjustments or settings to adapt to the operating conditions or installation environment. If you have trouble adjusting the camera, consult your dealer or an Authorized Sanyo Service Center. [. . . ]