User manual SANYO VCC-HD5600P FLYER

[. . . ] Itasca, IL 60143 708-775-1414 THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING HAWAII AND ALL U. S. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED. Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER (USA) CORPORATION warrants this SANYO product against defects in materials and workmanship for the periods specified below. [. . . ] They are referred to as internal amplifier type lens. B A 1/3 inch solid state image device CCD CS type lens mount C mount lenses can also be used with the supplied C mount adaptor. High speed electronic shutter 8 speeds, selectable by switches. English 3 PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odor comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Center). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer (or a Sanyo Authorized Service Center). Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera. If used with a foreign object inside, it could cause a fire, short-circuits or damages. If water or a liquid gets inside the camera, disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Center). Be careful to protect the camera from rain, sea water, etc. Be careful when handling the unit To prevent damages, do not drop the camera or subject it to strong shock or vibration. Install away from electric or magnetic fields If installed close to a TV, radio transmitter, magnet, electric motor, transformer, audio speakers the magnetic field they generate will distort the image. (For VIDEO type lenses, please refer to page 7. ) Set the A. I. The factory default setting is DC. 3 6 English PREPARATION 1 DC VIDEO 5 4 2 3 L Installation of a VIDEO type lens (sold separately) 1/2 or 2/3 inch C mount type (Flange-back: 17. 526 mm) LENS connector layout 1: +12 V DC (50 mA max. ) 2: Not used 3: Video output (1. 0 Vp-p, high impedance) 4: Ground (for video signal and DC power) 1 2 3 Remove the lens mount cap. Attach the supplied C mount adaptor to the auto-iris lens. Install the auto-iris lens onto the camera. 2 1 2 1 CAUTION: Do not use a lens if the length "L" is more than 5 mm. That may damage the camera and prevent proper installation. 4 3 4 3 4 Check the lens specifications sheet to make sure the lens iris plug layout is compatible with the layout of the LENS connector on the side of the camera. 5 CAUTION: If the lens iris plug shape and/or the connections layout are different, the supplied lens iris plug will have to be fitted, in order to be able to connect the lens to the LENS connector on the side of the camera. Set the A. I. Set the ALC and LEVEL controls on the lens to adjust the iris. LENS VR403 VR402 C: White balance (See page 11) A:Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. B: Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR401) volume when shooting in the conditions described below. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast L E V E L 1 2 3 4 Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+). Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens. Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ. [. . . ] (See page 3. ) EI ON OFF ON BLC CAUTION: · The electronic iris is suitable for normal indoor use. When the EI/BLC switch is set to the EI-ON position, do not use an auto-iris lens. BLC English 11 If using a VIDEO type auto-iris lens · The ALC volume on the lens should be turned all the way to Av (Average). · If the backlight compensation function does not compensate properly for the conditions, set using the LEVEL volume on the lens. Table B Electronic Shutter Speed 1/60 sec. (OFF/ON/ON/ON) Switch position ON ON CAUTION: The electronic iris function and the backlight compensation function cannot operate simultaneously. ON F: High speed electronic shutter setting Normally, the speed setting switches for the high speed ES (electronic shutter) are all set to the OFF position. [. . . ]