User manual SANYO VPC-CA100EX

[. . . ] GUIDE FOR BASIC OPERATION Dual Camera VPC-CA100EX VPC-CA100GX VPC-CA100PX VPC-CA100TA VPC-CA102 Important note This manual explains how to safely operate the VPC-CA100EX, VPC-CA100GX, VPC-CA100PX, VPC-CA100TA and VPC-CA102. Any information regarding only one of these products will be labeled as such. Please read these instructions carefully before using the camera. Make sure to read and understand the separate booklet "SAFETY MANUAL". [. . . ] <Caution> i Due to the characteristics of the camera, the outer surface may become warm during use, but this does not indicate a malfunction. i If the camera starts to feel uncomfortably hot during use, you might temporarily discontinue use until it cools down, or try holding it in your other hand for a while. Please use a tripod or other support when using the camera for a long time. 19 English DATE AND TIME SETTING The camera will record the date and time an image or audio recording is taken so that you can display them during playback. Therefore, before capturing images, make sure the correct date and time are set. h To correct the date and time setting, please see under HINT on page 21. on December 24, 2010 1 Turn on the camera (page 17), and press the SET button. h Follow the procedures below to enable or disable the date display during playback, to set the display format for the date, and to set the date and time. h To display the Recording or Playback Screen, press the MENU button 2 times. 3 Set the date to "2010/12/24". h The date is set in the following order: Set the year Set the month Set the day. h Press [G] or [H] to select year, month or day. Press [I] or [J] to increase or decrease the number. 4 Press the SET button. SETUP CLOCK SET DATE TIME DISP 2010/05/01 00:00 D/M/Y OK 2 CLOCK SET DATE 2010/12/24 OK English 20 3 Set the clock. h The time is set in the following order: Set the hour Set the minute. h A 24-hour clock is used for the time display. Set the order in which the date is displayed during playback. 4 Press the SET button. CLOCK SET TIME 19:30 OK 4 CLOCK SET DISP D/M/Y OK 5 Press the MENU button. h The date and time setting is completed. h To display the Recording or Playback Screen, press the MENU button. HINT i Under normal conditions, while the battery pack is being replaced, an internal battery will maintain the date and time settings. However, there is a small chance the settings may be lost (the backup will last for about 7 days). It is recommended to check that the date and time settings are still correct after replacing the battery pack and before shooting or recording of any type (follow step 1). To correct the date and time settings 1 Turn on the camera. [. . . ] SD Memory Card 8 GB 1, 200 images 1, 480 images 1, 130 images 1, 690 images 2, 240 images 10, 800 images 11, 300 images 20, 700 images 49, 800 images 1, 690 images 11, 300 images 1 hr. 16 GB 2, 340 images 2, 890 images 2, 210 images 3, 300 images 4, 370 images 21, 100 images 22, 000 images 40, 400 images 97, 100 images 3, 300 images 22, 000 images 2 hr 2 hr. 130 hr. Still image mode i If the continuous recording time of a voice memo exceeds about 13 hours, the recorded file is saved once, and then recording continues in a new file. In the video clip recording mode, when the size of the file being recorded exceeds 4 GB, the recorded file is saved once, and then recording continues in a new file. [. . . ]