User manual SATO CL612E SERVICE MANUAL

[. . . ] CL608e/CL612e Printers Service Manual PN 9001079 Rev. Charlotte, NC 28273 Main Phone: (704) 644-1650 Technical Support Hotline: (704) 644-1660 Fax: (704) 644-1661 http:\\www. satoamerica. com ã Copyright 2002 SATO America, Inc. The information supplied in this manual was current at time of publication. If you come across procedures that need clarification or find errors or have suggestions contact us at qc@satoamerica. com Warning: This equipment complies with the requirements in Part 15 of . CC rules for a Class B computing device. Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference. [. . . ] Mechanical Adjustments Ribbon Clutch Adjustments 5. 2. 2 Ribbon Rewind Clutch Adjustment STEP 1. PROCEDURE Connect the power cable to the printer and AC outlet. Raise the access door and remove the ribbon and label stock if installed. 5-1 Attach string to an empty ribbon core and place on the Ribbon Rewind Spindle. Wind the string tightly around the ribbon core in a single layer and in a clockwise direction. Attach the free end of the string to the tension gauge. 5-2 & 5-4 Gradually lift the tension gauge, pulling the string to unwind it from the core. Once the spindle begins to move the gauge should indicate 950 to 1050 grams of tension. Excessive or insufficient tension must be corrected by adjusting the ribbon unwind clutch. 5-2 & 5-4 To adjust the clutch, loosen the locking screw and move the adjust nut CW for more tension and CCW for less tension. Tighten the locking screw and repeat Steps 3 and 4 until the correct tension is achieved. 4. 5. Page 5-4 SATO CL608e/CL612e Service Manual PN 9001079 Rev. Mechanical Adjustments 5. 3 Print Head Position Adjustment Required Equipment: Allen Wrench 2. 5mm Ruler STEP 1. 2. PROCEDURE Refer to Section 7. 2 and run a test print. 5-5 By adjusting the Allen head screws on the rear of the Stay, you can move the print head forward or backward. This allows you to position the burnline of the print head directly and evenly over the apex of the platen surface. 5-6 & 5-7 While printing the test pattern, adjust the Allen adjustment screws for the best print quality. NOTE: It is vital that a known good platen be in the unit. Verify the image is even on the label by measuring the distance from the bottom of the barcode to the bottom of the label on both sides. If uneven, adjust the Allen adjustment screws to correct the alignment. This may affect the print quality and may need to be readjusted. If you are unable to get the unit to produce good print quality, proceed to Section 5. 4 Print Head Balance Adjustment and perform the adjustment; then return to this section and redo the Print Head Position Adjustment. NOTE: You may have to do both of these adjustments concurrently several times to achieve proper print quality and alignment. 3. 4. 5. PN 9001079 Rev. [. . . ] Parts List Dispenser Assembly Option PN 9001079 Rev. B SATO CL608e/CL612e Service Manual Page 10-35 Section 10. Parts List Dispenser Assembly Option NO. 1 2 3 4 5 6 7 8 9 12 13 14 15 16 17 18 19 20 21 24 25 26 27 28 29 30 CODE PH0720400 MH0300821 PA1724701 PB0721600 PB0721700 MD4300621 PA1724600 PA1724500 MD4300621 MD4301021 MD4300821 MA7300625 PA1724800 MD4300621 PB0721400 ND0030030 PE1720400 PE1570300 MH0250621 PA1724400 PR1340500 PR1520200 PB0721200 ND0040030 PC1010200 PE2730300 DESCRIPTION Dispense cover P tight screw Dispense frame Post (latch) RH Post (latch) LH Pan head screw Dispense bar Adjust plate Pan head screw Pan head screw Pan head screw Truss screw Dispense cover bracket Pan head screw Shaft (Guide) E-Ring Dispense bracket Dispense sensor bracket P-tight screw Roller bracket Brush Pressure roller sub assy Shaft (Pressure roller) E-Ring Head spring Stopper collar QTY 1 4 1 1 1 2 1 1 1 1 1 2 1 1 1 4 1 2 2 1 1 1 1 2 2 2 Page 10-36 SATO CL608e/CL612e Service Manual PN 9001079 Rev. [. . . ]