User manual SCUBAPRO R380

[. . . ] Caution: Do not score the threads on the valve body when applying the wrench. Scoring the threads will result in damage and require replacement of the valve body. 2003 SCUBAPRO 4 Important note: The following information is not designed to be a complete training guide for servicing the listed SCUBAPRO regulators. All SCUBAPRO technicians are required to attend an annual service training program to insure safe handling and servicing of SCUBAPRO products. All SCUBAPRO technicians must be employed by an authorized SCUBAPRO facility. SCUBAPRO R 390 - R 380 Second Stages P/N 43 04 00 00 No tools needed this step TOOLS NEEDED Push the valve housing to the inside of the case to remove. [. . . ] To remove the exhaust valve, grasp with fingers and pull firmly out. The exhaust valve will seldom need to be replaced. Careful inspection is usually all that is necessary. If the valve is removed during service, it may be damaged during the process, requiring replacement. This Step Is Only Performed As Needed If the exhaust valve is removed, carefully inspect and replace if necessary. Replace the exhaust tee center section and use the ball-end allen wrench to replace the exhaust tee pin. Inspect all washers and the lever. The nyloc nut should be adjusted as follows: a. Maximum of one poppet carrier thread showing through if used for a primary regulator. Maximum of two poppet carrier threads showing through if used for an octopus regulator c. Maximum of three poppet carrier threads showing through under all circumstances. 2003 SCUBAPRO 7 Important note: The following information is not designed to be a complete training guide for servicing the listed SCUBAPRO regulators. All SCUBAPRO technicians are required to attend an annual service training program to insure safe handling and servicing of SCUBAPRO products. All SCUBAPRO technicians must be employed by an authorized SCUBAPRO facility. SCUBAPRO R 390 - R 380 Second Stages Monoject Inspect and lubricate the two static o'rings on the valve body and adjustable orifice. Insert the adjustable orifice into the valve body and turn the adjustable orifice inward one complete turn using the universal tool. P/N 43 04 00 No tools needed this step 00 TOOLS NEEDED Install the valve housing and valve body into the case. Hold the lever DOWN while assembling these pieces. This will help prevent engraving of the poppet seat during the threading process. 2003 SCUBAPRO 8 Important note: The following information is not designed to be a complete training guide for servicing the listed SCUBAPRO regulators. All SCUBAPRO technicians are required to attend an annual service training program to insure safe handling and servicing of SCUBAPRO products. All SCUBAPRO technicians must be employed by an authorized SCUBAPRO facility. SCUBAPRO R 390 - R 380 Second Stages Use a 13mm or ½" low torque (thin) wrench to tighten the valve body. The wrench should rest on the "flat" sides of the valve body, which are designed to permit gripping by a wrench. Hold the lever arm down as you tighten the valve body to prevent engraving of the poppet seat. Caution: Do not score the threads on the valve body when applying the wrench. Scoring the threads will result in damage and require replacement of the valve body. Monoject Inspect and lubricate the valve body o'ring. [. . . ] Use the universal tool as shown to tighten. Insert the case pin. Mount the pneumatic adjusting tool into the second stage body, and thread on the second stage low-pressure hose. Use the pneumatic adjusting tool to make the initial air-on adjustments to the second stage, and to stop all free flowing. Once free flow stops, de-tune the second stage orifice from the twelve o'clock position to the one o'clock position. 2003 SCUBAPRO 11 Important note: The following information is not designed to be a complete training guide for servicing the listed SCUBAPRO regulators. [. . . ]