Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SEAGATE ATLAS IV. We hope that this SEAGATE ATLAS IV user guide will be useful to you.
Lastmanuals help download the user guide SEAGATE ATLAS IV.
Manual abstract: user guide SEAGATE ATLAS IVDATASHEET
Detailed instructions for use are in the User's Guide.
[. . . ] Atlas IV
68-Pin Jumper Settings
68-Pin Jumper Settings
The following describes the jumper options and settings available on the Maxtor® AtlasTM IV disk drive. [. . . ] Using these jumper pins you can establish the various drive configuration options. The secondary option jumper block (12-pin) provides an alternate method for setting primary drive features. The alternate jumper block is located at the rear of the drive and is incorporated into the SCSI cable connector.
Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27
Signal logic_gnd logic_gnd logic_gnd logic_gnd Fault LED logic_gnd logic_gnd NC +5V out logic_gnd logic_gnd logic_gnd logic_gnd Term Power (TP)
Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28
Signal SCSI ID (A3) SCSI ID (A2) SCSI ID (A1) SCSI ID (A0) Blank (Key, no pin) Spin Delay (DS) Force SE (SE) NC Busy Out Write Protect (WP) Stagger Spin (SS) No Wide (NW) Reserved Term Power (TP)
3 of 3
Atlas IV
68-Pin Jumper Settings
Pin 1 3 5 7 9 11
Signal SCSI ID (A0) SCSI ID (A1) SCSI ID (A2) SCSI ID (A3) NC LED Pwr (+5V)
Pin 2 4 6 8 10 12
Signal XTFault logic_gnd logic_gnd Busy LED logic_gnd NC
SCSI ID Settings The following table identifies the various SCSI ID values and the jumper positions required to set them. A0 (Pins 7-8) OFF ON OFF ON OFF ON OFF ON OFF ON A1 (Pins 5-6) OFF OFF ON ON OFF OFF ON ON OFF OFF A2 (Pins 3-4) OFF OFF OFF OFF ON ON ON ON OFF OFF A3 (Pins 1-2) OFF OFF OFF OFF OFF OFF OFF OFF ON ON
Drive ID
ID 0 ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 ID 9
4 of 4
Atlas IV
ID 10 ID 11 ID 12 ID 13 ID 14 ID 15 OFF ON OFF ON OFF ON ON ON OFF OFF ON ON OFF OFF ON ON ON ON
68-Pin Jumper Settings
ON ON ON ON ON ON
5 of 5
Atlas IV
80-Pin Jumper Settings
80-Pin Jumper Settings
The following describes the jumper options and settings available on the Maxtor® AtlasTM IV SCA disk drive. For more detail on jumper definitions; please refer to the jumper definition section. The Maxtor Atlas IV was developed by Quantum Corporation prior to its merger with Maxtor.
Fo rce SE (SE)
Enable Single Ended operation Enable auto switch between Single Ended or LVD operation * Indicates default jumper setting
SE jumper on SE jumper off*
The Atlas IV SCA drive does not provide support for any additional options through the use of physical jumper settings. Additional feature options are set through the SCA interface, contact your system manufacturer for details on how to set optional features. The Atlas IV SCA provides support for: Stagger Spin, Spin Delay and SCSI ID selection.
1 of 1
Atlas IV
The Atlas IV SCA does not provide support for: Active Termination enable, Termination Power and Write Protect.
80-Pin Jumper Settings
Jumper Locations
The Atlas IV SCA disk drive has only one location (J7 on PCB) where user configurable jumpers are found. [. . . ] Contact your system manufacturer for details on setting SCSI ID.
2 of 2 [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SEAGATE ATLAS IV
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SEAGATE ATLAS IV will begin.
