User manual SEAGATE FIREBALL SE JUMPER SETTINGS ATA

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SEAGATE FIREBALL SE. We hope that this SEAGATE FIREBALL SE user guide will be useful to you.

Lastmanuals help download the user guide SEAGATE FIREBALL SE.

Download

You may also download the following manuals related to this product:

SEAGATE FIREBALL SE MOUNTING GUIDELINES (100 ko)

SEAGATE FIREBALL SE JUMPER SETTINGS SCSI (45 ko)

Manual abstract: user guide SEAGATE FIREBALL SEJUMPER SETTINGS ATA

Detailed instructions for use are in the User's Guide.

 [. . . ] Fireball SE
Jumper Settings

ATA Jumper Settings
DS Stand Alone Master with Slave Present Slave to Master ON ON OFF CS OFF OFF OFF PK X X X Rsvd OFF OFF OFF

X = PK is a Parking position.  [. . . ] The jumper block is incorporated into the IDE / ATA cable connector. Using the jumper pins you can establish the drive Master/Slave configuration. 

1 of 1

Fireball SE

fireball_se_jumper. pdf

BIOS Settings The following BIOS parameters are provided for customers needing to manually configure the Quantum disk drive. Both base 2 and base 10 capacity values are displayed. Cylinders 2. 1 GB 3. 2 GB 4. 3 GB 6. 4 GB 8. 4 GB 4092 6256 14848 13328 16383 Heads 16 16 9 15 16 Sectors 63 63 63 63 63 Base 2 Capacity 2, 014 MB 3, 079 MB 4, 110 MB 6, 149 MB 8, 063 MB Base 10 Capacity 2, 111 MB 3, 228 MB 4, 310 MB 6, 448 MB 8, 455 MB

Special Considerations Hard drives greater than 2. 1GB may need to be divided into multiple partitions / logical drives. MS-DOS versions 4. 0 through 6. 22 allow a maximum primary partition / logical drive size of 2. 1GB and are limited to 8. 4GB in physical drive capacity. The file systems supported by Windows-95,  Windows-98 and Windows NT are not restricted to the 8. 4GB physical drive limit,  but special BIOS support is required. 

SCSI Jumper Settings
The following describes the jumper options and settings available on the Fireball SE drive. For more detail on jumper definitions; please refer to the jumper definition section. Termination Enable (TE) Enable termination Disable termination TE jumper on TE jumper off

SCSI ID (A2,  A1,  A0) Set drive SCSI ID See ID settings table below

Park (PK) Used for spare jumper N/A

Jumper Locations The Fireball SE disk drive has only one location where user configurable jumpers are found.  [. . . ] Drive ID ID 0 ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 A0 OFF ON OFF ON OFF ON OFF ON A1 OFF OFF ON ON OFF OFF ON ON A2 OFF OFF OFF OFF ON ON ON ON

3 of 3 [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SEAGATE FIREBALL SE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SEAGATE FIREBALL SE will begin.