User manual SEAGATE MOMENTUS BLADE SERVER
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SEAGATE MOMENTUS BLADE SERVER. We hope that this SEAGATE MOMENTUS BLADE SERVER user guide will be useful to you.
Lastmanuals help download the user guide SEAGATE MOMENTUS BLADE SERVER.
Manual abstract: user guide SEAGATE MOMENTUS BLADE SERVER
Detailed instructions for use are in the User's Guide.
[. . . ] Momentus Blade Server
ST94811AB
Momentus Blade Server
ST94811AB
©2004, Seagate Technology LLC All rights reserved Publication number: 100339697, Rev. A June 2004 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. DiscWizard, SeaTools, SeaFONE, SeaBOARD, SeaTDD, 3D Defense System and the Wave logo are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. [. . . ] A
3. 0
Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
3. 1
Handling and static discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: · Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive's exposure to ESD. · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Handle the drive only by its edges or frame. · The drive is fragile--handle it with care. Do not press down on the drive top cover. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.
3. 2
3. 2. 1
Jumper settings
Master/slave configuration
Use the options jumper block shown in Figure 3 to configure the drive for operation. This jumper block is the 4pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable select option, see Section 3. 2. 2. The "Master or single drive" option is the factory default setting.
Drive is master (or single drive) Drive is slave Cable select
Figure 3. Jumper settings
Momentus Blade Server Product Manual, Rev. A
15
3. 2. 2
Cable-select option
Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper as shown in Figure 3. Refer to your computer manual to determine whether your computer supports this option.
3. 3
Drive mounting
You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive: · Allow a minimum clearance of 0. 030 inches (0. 76 mm) around the entire perimeter of the drive for cooling. [. . . ] If your location is not listed here, dial our European warranty service center at +31-20-316-7222 from 8:30 A. M. (Central Europe time) Monday through Friday. The warranty service center is located in Amsterdam, The Netherlands.
Toll-Free Support Numbers
Call Center Austria Belgium Denmark France Germany Ireland Italy Netherlands Norway Poland Spain Sweden Switzerland Turkey United Kingdom Presales and Technical Support 0 800-20 12 90 00 800-47324283 (00 800-4SEAGATE) 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-311 12 38 00 800-47324283 00 800-47324283 00 800-47324283 00 800-31 92 91 40 00 800-47324283 Warranty Service 0 800-20 12 90 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-311 12 38 00 800-47324289 00 800-47324289 00 800-47324289 00 800-31 92 91 40 00 800-47324289
FAX Services--All Europe (toll call)
Technical Support Warranty Service +1-405-324-4702 +31-20-653-3513
Africa/Middle East Support Services
For presales and technical support in Africa and the Middle East, dial our presales and technical support call center at +1-405-324-4714 from 8:00 A. M. (Central Europe time) Monday through Friday. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SEAGATE MOMENTUS BLADE SERVER
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SEAGATE MOMENTUS BLADE SERVER will begin.
