User manual SEAGATE ULTRA ATA133 PCI ADAPTER CARD INSTALLATION
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SEAGATE ULTRA ATA133 PCI ADAPTER CARD. We hope that this SEAGATE ULTRA ATA133 PCI ADAPTER CARD user guide will be useful to you.
Lastmanuals help download the user guide SEAGATE ULTRA ATA133 PCI ADAPTER CARD.
Manual abstract: user guide SEAGATE ULTRA ATA133 PCI ADAPTER CARDINSTALLATION
Detailed instructions for use are in the User's Guide.
[. . . ] After installing the Ultra ATA/133 PCI Adapter Card and connecting the hard drives, format and partition the drives using the software included with the drives. Install Windows 9x/Me using your Windows installation diskettes or CD. After installation, go to the "Start" menu and select "Settings. " 4. From the "Settings" menu, select "Control Panel. " 5. [. . . ] · Option A: Installing Drivers with a New Windows 98/Me Installation · Option B: Installing Drivers with an Existing Windows 98/Me Installation · Option C: Installing Drivers During a New Windows NT 4. 0/2000/XP Installation · Option D: Installing Drivers with an Existing Windows NT 4. 0/2000/XP Installation 8. Select the "Driver" tab in the "Properties" window, choose "Update Driver. . . " and then press "Next. "
32-pin PCI connector
Figure 2 Adapter Card Connections
5. Fasten the adapter card bracket to the system case.
Note: If, upon booting, your system doesn't recognize the adapter card, change the card to a different PCI slot. Maxtor recommends using one of the first 3 slots nearest to the processor.
Striped Edge (Pin 1)
ATAPI Devices (DVD-ROM, Tape Backup)
If your ATAPI device (CD, DVD, Zip, or tape) is not UDMA 66, 100 or 133 compliant and is functioning properly, please leave it on its current ATA channel. These devices will not benefit from the additional performance provided by this card.
Drive 1 - Slave (gray) Adapter Connector (blue)
Figure 3 Ultra ATA Interface Cable
Drive 0 - Master (black)
www. maxtor. com
P/N: 20209900/B
Ultra ATA/133 Card Installation Guide
3
Install Drivers (cont. )
Option B: Installing Drivers with an Existing Windows 98/Me Installation
1. After installing the Ultra ATA/133 PCI Adapter Card and connecting the hard drives, power up the system and boot into Windows. The "Add New Hardware Wizard" will appear, informing you that it has found a "PCI Mass Storage Controller. " Refer to steps 9 through 13 of Option A to complete the driver installation, then format and partition your hard drives using the software provided with the drives.
Option D: Installing Drivers with an Existing Windows NT 4. 0/2000/XP Installation
Note: The Ultra ATA/133 drivers must be installed in Windows on the boot drive (running off of an existing ATA port) before you connect any hard drives to the Ultra ATA/133 card. Note: The screenshots under Option A are also applicable for an Option D installation. Select "Settings" from "Start" menu. Select "Control Panel" from the "Settings" menu. Open the "System" control panel.
9. Select "Search for a better driver than the one your device is using now (recommended), " and press "Next. "
Option C: Installing Drivers during a New Windows NT 4. 0/2000/XP Installation
Note: Before installing Windows NT, 2000, or XP, the Maxtor Ultra ATA/133 card drivers must be extracted from the MaxBlast CD. Change the boot sequence or boot order in your system BIOS to "A>CD-ROM>C" or "Diskette Drive, CDROM, Hard Disk. " 2. Boot your system to the MaxBlast CD, and select the "Create Maxtor Ultra ATA Driver Diskette" option. Follow the onscreen prompts to create the driver diskette. Depending on the type of Windows installation media you have, perform one of the following OS installations: a. Floppy Install: Boot the system using the Windows installation diskettes. CD-ROM Install: Insert the Windows Install CD, reboot your system, and follow the on-screen prompts. When prompted by the installer, press 'S' to Specify An Additional Device(s). Insert the Maxtor Ultra ATA Driver Diskette into the floppy drive and press the "Enter" key. In the "Browse for Folder" window that appears, select your CD-ROM drive letter. Select the "Win9x-Me" folder, then click "OK. " 8. [. . . ] For a replacement Ultra ATA/133 PCI Adapter Card, the warranty on the replacement card is the remainder of the warranty on the original card or 90 days, whichever is longer. If you discover a defect, Maxtor will replace the Card at no charge to you, provided you return it during the warranty period, with transportation charges prepaid, to Maxtor in Ireland, Singapore or the USA. Ultra ATA/133 PCI Adapter Cards must be properly packaged in Maxtor packaging or Maxtor approved packaging to obtain warranty service. Before returning a Maxtor Adapter, please contact Maxtor at: +353 1 204 1111 (in Europe) or 1-800-2MAXTOR (in U. S. ) to obtain a Return Material Authorization (RMA) number. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SEAGATE ULTRA ATA133 PCI ADAPTER CARD
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SEAGATE ULTRA ATA133 PCI ADAPTER CARD will begin.
