User manual SEGA ACROSS THE WORLD SAMMY

[. . . ] Please do not bend or press the connector wires. Insert the Scoreboard set (including the overhead bar) into the overhead bar bracket , NOTE : the part with the connector plugs should face inside. Connector plug end Connector plug end need to pass through the overhead bar bracket first set Insert trough Step 8 :Plug-in all the plugs on the connector plug end in accordance to its colors. NOTE: plug-in tightly. All plugs are separated by colors 8. Assemble Instruction Step 9 :Use the open - cut side of the overhead bar plastic cover, and then insert it into the overhead bar protection cover. Lastly attach the whole cover onto the side panel . Before attaching it on , ensure the overhead bar is placed into the open - cut of the overhead bar plastic cover . [. . . ] Then cover it with the overhead bar protection cover. Open-cut Plastic cover with the plastic bar bracket cover then place the set onto the overhead bar Place the plastic bar bracket cover onto the overhead bar plastic cover Step 10 :Tightly screw on the plastic bar bracket cover on both sides with ( 4 ) big flathead screw ( 5 mm x 35 mm ). The center guard needs to be attached into the ( 2 ) upper holes of the plastic bar bracket cover . Center guard needs to be attached into the 2 upper holes Use 4 big flathead screw (5mm x 35mm) FINISHED PICTURE 9. Assemble Instruction Step 9 :Use the open - cut side of the overhead bar plastic cover, and then insert it into the overhead bar protection cover. Lastly attach the whole cover onto the side panel . Before attaching it on , ensure the overhead bar is placed into the open - cut of the overhead bar plastic cover . Then cover it with the overhead bar protection cover. Open-cut Plastic cover with the plastic bar bracket cover then place the set onto the overhead bar Place the plastic bar bracket cover onto the overhead bar plastic cover Step 10 :Tightly screw on the plastic bar bracket cover on both sides with ( 4 ) big flathead screw ( 5 mm x 35 mm ). The center guard needs to be attached into the ( 2 ) upper holes of the plastic bar bracket cover . Center guard needs to be attached into the 2 upper holes Use 4 big flathead screw (5mm x 35mm) FINISHED PICTURE 9. BG-X005-SGA Description of Motherboard Controls DIP Sw2 D IP S w 1 Game Test Transform SD card installment NO-NC button Volume adjustment knob LEDA: Running LED lights around Nc3 : Rail Strike Detector table NC2 : Display panel connection outlet NC313 : Direct Current (DC) Input outlet NC35 : A1 Output Control point NC36 : B1 Output Control point NC311 : Electro-magnet switch for goal gates (solenoid) NC4 : Rail Strike Detector NC310 : Blower output NC312 : Alternating Current (AC) Output NC40 : Rail Strike Detector R3 : Sound Effect and Volume adjustment NC41 : Rail Strike Detector VF1 : Total Volume Adjustment NC42 : Rail Strike Detector SPEAK : Sound Output NC43 : Strike Detector 10. BG-X005-SGA Description on locations of controls Winning light control board Power for motherboard Motherboard Display panel light and puck exit slot light control card Counters Motherboard: Controls the game operation, light signals and sounds of the machine. Power for Motherboard: Supplies the power to motherboard and other control cards. Winning light control card: Controls the winning lights on the score board. Display panel light and puck exit slot light control card: Controls the display panel lights and puck slot lights. ON/OFF switch is underneath the table , next to the power display. 2) Both coin acceptors and ticket dispensers are properly plugged in and connected. 3) Any damage to connection pins/other wirse. 4) Make sure both ticket dispensers are on the following settings N. O (Normally Open) and not on continuous dispense. 5) Both coin acceptors are on the N. O (Normal Open) settings. 6) The correct numbers of coins have inserted to play the game. VI. NOTE There is no start button located on commercial air hockey machines. 16. Care & Maintenance Keep these tips in mind for best operating performance Turn the adjustable leg bolts to create a leveled playing field . Place puck in the middle of the table: if it moves to a certain side, raise accordingly. Avoid direct sunlight if table is placed outdoors. [. . . ] Place puck in the middle of the table: if it moves to a certain side, raise accordingly. Avoid direct sunlight if table is placed outdoors. Avoid exposure to wetness when placed in basement or wet area. Do not shake or drop when transporting. [. . . ]