User manual SEGA FORD RACING TWIN

[. . . ] 420-FRSM-02UK REV 2 TWIN DRIVING CABINET SERVICE MANUAL · · Before using this product, read this MANUAL carefully to understand the contents stated herein. After reading this MANUAL, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. Manufactured in the UK by Amusements Europe Limited BEFORE USING THIS PRODUCT To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the use of QUALIFIED SERVICE PERSONNEL ONLY. After carefully reading and sufficiently understanding the instructions should any activity be carried out on the product. [. . . ] Displays test routines for steering force feedback system. Displays pages of various game information. Displays the setting for the internal clock. Displays test routine for communications. Displays menus for specific game test routines. Leaves System Test and returns to game mode. The operator uses the SERVICE button to select the desired test routines and presses the TEST button to activate choice. 27 10. 3. SYSTEM INFORMATION This test displays general system information regarding the hardware configuration and installed software. SYSTEM ID DISK IMAGE LAUNCHER VERSION GAME SHELL VERSION GAME NAME GAME VERSION UGCI VERSION IBUTTON EXIT A unique 64 bit ID code to identify the system Version number for master disk image Version number for System Launcher Version number for Game Shell Name of the installed game Version number of installed game Hardware version of installed UGCI board Type of iButton installed (Game Name or SYSTEM). If no iButton is installed, then a NOT FOUND message is shown Return to SYSTEM MENU The user cannot modify any of the parameters in this test. The user must press the TEST button to exit this test. 28 10. 4. UGCI TEST This test is used to test the network link between the computer and the UGCI board. COIN 1 COUNT COIN 2 COUNT VERSION UGCI STATUS EXIT Value of UGCI NVR coin count 1 Value of UGCI NVR coin count 2 Version number of UGCI board OK is the system can communicate with the UGCI board, otherwise a NOT CONNECTED message is shown. Return to SYSTEM MENU The user cannot modify any of the parameters in this test. The user must press the TEST button to exit this test. 29 10. 5. INPUT TEST This test is used to test and calibrate the peripherals connected to the UGCI interface. STEERING ACCELERATOR BRAKE GEAR SHIFT START CHANGE VIEW SERVICE TEST EXIT 00H = Full Left lock, 80H = Centre, FFH = Full right lock 00H = pedal fully up, FFH = pedal fully down 00H = pedal fully up, FFH = pedal fully down UP = stick up, N = stick central, DOWN = stick down On = pressed, OFF = not pressed On = pressed, OFF = not pressed On = pressed, OFF = not pressed On = pressed, OFF = not pressed Exit to System Menu Please refer to the CALIBRATION TEST for calibrating the hand and foot controllers. As this test will check for functionality of both the TEST and SERVICE buttons, in order to exit this test, BOTH buttons must be pressed simultaneously. 30 10. 6. CALIBRATION TEST This test is used to calibrate the analogue system input devices, i. e. the steering wheel, throttle pedal and brake pedal. STEERING LEFT VAL STEERING LEFT VAL BRAKE DOWN VAL BRAKE UP VAL THROTTLE DOWN VAL THROTTLE UP VAL CALIBRATE STEERING The current maximum left position of the steering wheel The current maximum right position of the steering wheel The current maximum down position of the brake pedal The current maximum up position of the brake pedal The current maximum down position of the throttle pedal The current maximum up position of the throttle pedal Starts the steering calibration routine. The user must follow the on screen prompts to turn the wheel full left and then full right for 5 seconds. CALIBRATE BRAKE Starts the brake calibration routine The user must follow the on screen prompts to fully depress and then release the brake pedal for 5 seconds. CALIBRATE THROTTLE Starts the throttle calibration routine. The user must follow the on screen prompts to fully depress and then release the throttle pedal for 5 seconds. EXIT Exit to System Menu The user will use the SERVICE button to select the desired test and the TEST button to activate the test. 31 10. 7. OUTPUT TEST This test is used to test any output signals (i. e. lamps) from the system. EXIT Exit to System Menu There are currently no output tests defined. Use the TEST button to return to the System Menu. 32 10. 8. COIN TEST This test is used to set coin related parameters. : COIN CHUTE COIN/CREDIT This option is fixed to COMMON This is used to select how many credits per play are required. There are currently two options : 1 indicates 1 credit per play, and FREEPLAY indicates that no credits are required for play. [. . . ] ASSY SEAT TWIN 1P ­ FR-5000UK SEQ 1 2 PT NUMBER FR-5500UK FR-5600UK DESCRIPTION ASSY SEAT CABI ASSY SEAT UNIT QTY 1 1 25. 10. ASSY SEAT CABI ­ FR-5500UK SEQ 1 2 3 7 PT NUMBER FR-5501UK MA1019 FR-5505UK 601-5699UK DESCRIPTION WOODEN SEAT CABI CASTER 75 JOINT PLATE LEG ADJUSTER M16X100 1L/NUT QTY 1 3 2 4 93 25. 11. ASSY SEAT UNIT ­ FR-5600UK SEQ 1 2 4 15 16 101 102 103 PT NUMBER FR-5601UK FR-5602UK FR-5604UK 610-0408-91 RND-0039 RND-0063-01 601-9059-91 601-9060-91 DESCRIPTION SEAT BASE SHIFT ENCLOSURE SEAT ADAPTOR PLATE UP/DOWN SHIFTER AL PLATE U/D SHIFT MTNG SEAT MIDWAY 04-12452 RAL5005 SEAT RAIL L SEAT RAIL R QTY 1 1 1 1 1 1 1 1 94 25. 12. ASSY AC BRKT MAIN ­ FR-0400UK SEQ 1 101 102 107 301 601 PT NUMBER HDF-0661UK EP1382 EP1387 LB1096 FR-60011UK 514-5078-10000 DESCRIPTION BRKT AC HDF FILTER SCHAFFNER FN682-10/06 IEC INLET & SW BZV01/Z0000/70 STICKER PROTECTIVE EARTH WIRE HARNESS AC BRKT FR (NOT SHOWN) FUSE 5X20 CERAMIC SB 10A QTY 1 1 1 1 1 1 25. 13. [. . . ]