User manual SEGA NAOMI 50

[. . . ] HANDLING AND INSTALLATION PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. 2. COIN HANDLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. 3. NAME OF PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. 4. ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3. 5. [. . . ] Place the LINDBERGH into the outer packaging and fold around Game Board as shown. Slide the unit into the carton and seal. 9 3. 5. ASSEMBLY INSTRUCTIONS · Perform the assembly by following the procedure herein stated. Failure to comply with the instructions, for example, inserting the plug into an outlet at a stage not mentioned in this manual can cause an electric shock · Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling can cause damage to the machine, or malfunction to occur. · Do not attempt to complete this work alone, a minimum of 2 people are required. · Only QUALIFIED SERVICE PERSONNEL should carry out assembly. When carrying out the assembly work, follow the procedure in the following three item sequence: STEP 1 STEP 2 STEP 3 INSTALLING THE BILLBOARD SECURING IN PLACE (LEG ADJUSTER ADJUSTMENT) CONNECTION TO THE POWER SUPPLY Note that the parts contained within the installation kit are required for the assembly work. The following tools will be required when installing this machine: WRENCH (FOR M4 TAMPERPROOF SCREW) 10 3. 5. 1. INSTALLING THE BILLBOARD · Only QUALIFIED SERVICE PERSONNEL should carry out this operation. 1. Insert ASSY BILLBOARD to the top part of the cabinet 2. Secure with the two Tamperproof screws 11 3. 5. 2. SECURING IN PLACE (LEG ADJUSTER ADJUSTMENT) · Make sure all of the leg adjusters are in contact with the floor. Such damage could result in a fire or electric shock. · Do not push the upper part of the cabinet. Failure to observe this can cause the cabinet to fall forwards and result in accidents. · When transporting the machine, be sure to hold the catch portion on the rear of the cabinet with the castors making contact with the surface as shown below. Inclining the machine by holding portions other than the catch or moving the cabinet without retracting the adjusters can damage the cabinet and/or the floor surface. Failure to observe this may damage the installation portions and may cause unexpected accidents. · This operation should only be carried out by QUALIFIED SERVICE PERSONNEL. 15 16 3. 7. INTERNAL SWITCHES AND COIN METERS · Never touch places other than those specified. Touching places not specified can cause electric shock and short circuits · Be careful not to damage wiring. Damaged wiring can cause electric shock and short circuits. · Adjust to the optimum sound volume considering the environmental requirements of the installation location. The Control Panel Base can be opened by unlocking as shown below. Internal switches can be accessed when the Base is opened. 17 TEST SWITCH SERVICE SW 1 SERVICE SW 2 DEMAG. [. . . ] 1 2 3 4 101 103 104 202 203 204 205 PART NUMBER NOA-1481XUK NOA-1482 NOA-1483 NOA-1484UK 220-5086-AUK 220-5086-CUK 000-F00408 000-P00308 060-S00300 060-L00300 060-F00400 QTY 1 1 1 2 1 2 5 1 1 1 1 DESCRIPTION BASE COIN SELECTOR LINK COIN CHUTE UPPER COIN CHUTE ADHESIVE INSULATING PAD MECH CADDY BASE MECH CLIP M4X8 MSCR CSK PAS M3X8 MSCR PAN PAS M3 WSHR SPR PAS M3 WSHR LOCK PAS M4 WSHR FORM A FLT PAS COMPONENT REFERENCE (3)-2, (101)-3 (2)-1 (2)-1 (2)-1 (2)-1 47 8. 10. NOB-1480 ASSY COIN SELECTOR UNIT 220 No. 1 2 3 201 202 PART NUMBER NOB-1481UK NOB-1482 NOB-1484 045-0037 000-P00408-W QTY 1 1 1 1 2 DESCRIPTION BASE COIN SELECTOR LINK COIN SELECTOR 220 L HOOK DIA6 SNAP PIN M4X8 MSCR PAN W/FS PAS COMPONENT REFERENCE (3)-2 48 8. 11. NOA-1500UK ASSY FRONT PANEL (COM) No. [. . . ]