User manual SEGA UFO CATCHER

[. . . ] TABLE OF CONTENTS BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS INTRODUCTION 1 HANDLING PRECAUTIONS ··················································1 2 PRECAUTIONS REGARDING INSTALLATION LOCATION················4 2-1 LIMITATIONS OF USAGE ······················································································4 2-2 OPERATION AREA ································································································5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 3 PRECAUTIONS REGARDING PRODUCT OPERATION ···················6 3-1 BEFORE OPERATION····························································································6 3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS) ·····························7 4 PART DESCRIPTIONS ························································8 5 ACCESSORIES ································································9 6 INSTALLATION ·······························································11 6-1 SECURE THE UNIT AT THE INSTALLATION SITE (MANIPULATE THE ADJUSTERS) ··············································12 6-2 REMOVE SHIPPING BRACKETS ·········································································13 6-3 ATTACH PARTITION·····························································································15 6-4 CONNECT POWER CORD ···················································································16 6-5 ACTIVATE POWER SUPPLY ················································································17 7 PRECAUTIONS WHEN MOVING ···········································18 8 PRIZE REPLACEMENT ·····················································19 9 GAME CONTENT ····························································21 10 GAME BOARD ·······························································23 11 EXPLANATION OF TEST AND DATA DISPLAY ···························25 11-1 SWITCH UNIT AND CASH BOX ··········································································25 11-2 VFD DISPLAY CONTENT ···················································································26 11-3 EXPLANATION OF TEST MODE ·········································································31 ··························································33 12 DIP SW SETTINGS E1-0605 420-6953 i 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 13 ARM MECHANISM 13-1 ARM REPLACEMENT ························································································37 13-2 ADJUSTMENT OF SENSOR BRACKET POSITION ·············································40 13-3 SPRING STRENGTH ADJUSTMENT AND SPRING REPLACEMENT ···················43 13-4 SHOVEL REPLACEMENT AND ADJUSTMENT ··················································45 13-5 OPEN ARM ANGLE ADJUSTMENT ····································································46 ··························································37 14 MAINTENANCE OF Z-ORIENTED MECHANISM ··························47 15 COIN SELECTOR ····························································49 15-1 REMOVING THE COIN SELECTOR ····································································49 15-2 REMOVING A JAMMED COIN ············································································50 15-3 CLEANING THE COIN SELECTOR ·····································································51 15-4 COIN INSERTION TEST ·····················································································51 16 REPLACEMENT OF FLUORESCENT LIGHTING, LAMPS, AND FUSES········52 16-1 FLUORESCENT LIGHTING REPLACEMENT ······················································52 16-2 LAMP REPLACEMENT ·······················································································53 16-3 FUSE REPLACEMENT ·······················································································56 17 PERIODIC INSPECTION ····················································57 18 ERROR MESSAGES ·························································58 19 TROUBLESHOOTING ·······················································59 20 DESIGN-RELATED PARTS··················································60 21 OPTIONAL ITEMS····························································61 21-1 DOLLAR BILL VALIDATOR ················································································61 21-2 SECURITY BAR ·································································································63 21-3 LCD UNIT (LCD CASE + CABLE COVER)···························································67 22 PARTS LIST ··································································75 23 WIRE COLOR CODE TABLE···············································114 24 WIRING DIAGRAM ·························································115 ii INTRODUCTION This manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electro-mechanicals, servicing control, spare parts, etc. for the product, "SEGA UFO CATCHER". This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and sufficiently understanding the instructions. [. . . ] If the limit sensor is entered or operation has just begun, "0" is displayed. TABLE 11-3b Test Mode Number Test mode 1 7-Seg Display Reads 7-seg 1 7-seg 2 7-seg 3 7-seg 4 7-seg 1 7-seg 2 7-seg 3 7-seg 4 7-seg 1 7-seg 2 7-seg 3 7-seg 4 7-seg 1 7-seg 2 7-seg 3 7-seg 4 (Down switch also lights up in response to prize sensor) Content Limit sensor LEFT Limit sensor RIGHT Limit sensor FWD Limit sensor BACK Limit sensor UP Limit sensor DOWN ­­­ ­­­ Open sensor ­­­ ­­­ ­­­ Prize sensor ­­­ ­­­ ­­­ Test mode 2 Test mode 3 Test mode 4 11 EXPLANATION OF TEST AND DATA DISPLAY 32 12 DIP SW SETTINGS Turn off the power supply before changing DIP SW. If the power is left on while DIP SW are changed, electrical shock may occur. IMPORTANT · Make sure the DIP SW that are designated to be OFF are turned OFF. If DIP SW are set to other than prescribed settings, there will be instances when behavior is not suited to actual operations. · Changed settings do not become effective until the power supply has been reactivated after changing DIP SW. · The DIP SW on the game board are not used for game settings but must all be set to OFF. With this product, settings can be changed to those shown in the table by changing the DIP SW (DIP Switch) settings on the switch unit. DIP SW 1 adjusts coin credit settings; DIP SW 2 sets common game operations for 1P and 2P; DIP SW 3 and 4 set the game operations for 1P and 2P, respectively. 12 DIP SW SETTINGS FIG. 12 COIN SETTINGS DIP SW 1~4 Coin credit settings (credits awarded per coin) are set using DIP SW 1. When 9 credits are exceeded, no more coins are accepted and the coins are returned. However, if 1 coin is worth 2 credits or more, and 8 credits are remaining, 10 credits or more are established (10 credits or more can be established, depending on the setting). For example, if it is set so that 1 coin equals 2 credits and 8 credits have been established, the total becomes 10 credits when the next coin is inserted. At this time, the 7-seg displays blink alternately between "1" and "0" and no more coins can be accepted. When FREE PLAY is selected, " " is shown on the 7-seg display and games can be played without engaging the coin and service switches. SETTING COMMON GAME OPERATIONS FOR 1P AND 2P Common game operations for 1P and 2P are set with DIP SW 2. BGM SOUND Sounds for when the unit is in customer-standby status or when a game is being played can be set. BGM1: Two music pieces change each time a game is completed. BGM2: Game music is played also while in customer-standby status. BGM3: Two Christmas songs change each time a game is completed. BGM4: No music is heard during customer-standby status or game play. 33 METER SETTINGS TOTAL COIN (BILL=4COIN) / TOTAL PRIZE - METER 1: 1P + 2P total coins are counted. - METER 2: 1P + 2P total prizes are counted. TOTAL COIN (25¢) /TOTAL BILL ($1) - METER 1: 1P + 2P total 25-cent coins are counted. - METER 2: 1P + 2P total $1-bills are counted. 1P PRIZE/2P PRIZE - METER 1: 1P prizes are counted. [. . . ] The tolerance is +/-2mm. (Earth terminal) (D-1/2) Details of part "B" (NOT TO SCALE) (D-2/2) ITEM NO. PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 37 38 39 41 42 43 47 48 49 50 51 52 53 54 57 58 61 62 UCU-1000 UCU-1100 UCU-1110 UCU-1150 UCU-2000 UCU-3000 UCU-3010 UCU-3100 UCU-3200 UCU-3300 UCU-3400 UCU-4000 UCU-0001 UCU-0002 UCU-0003 UCU-0004 UCU-0005 UCU-0006 UCS-0007 UCU-0007 UCU-0008 UCU-0009 UCU-0010 UCU-0011 UCU-0012 UCU-0013 UCU-0014 UCU-0015 UCU-0016 UCU-0017 UCU-0042 DP-1148X UCU-0018 421-11416 421-8479-01 421-7974-01 421-6690-01 440-WS0002XEG 440-WS0286-EG 440-WS0027-EG 421-12116 UCU-1002-B UCU-1002-C UCU-1002-D UCU-1002-E UCU-1002-F 621-000110-US 421-6119-91 440-CS0316-EG UCU-0040 UCU-0041 DESCRIPTION NOTE 101 102 103 104 105 106 201 202 203 204 206 207 208 209 210 211 212 213 214 215 216 217 218 219 301 302 401 403 404 405 406 407 408 409 410 411 413 414 415 220-5794 390-6836-32 390-6836-25 280-5275-SR10 601-0460 280-5124-04 000-P00408-W 000-T00408-0C 008-T00408-0C 008-T00412-0C 000-P00425-S 050-F00400 068-441616-0C 068-552016-0C 000-P00406-0C 000-P00410-0C 000-P00410-W 020-000410-0Z 060-F00400 060-S00400 FAS-600004 050-F00600 031-000620-0C 008-T00416-0C UCU-60016 UCU-60026 601-6604-70 420-6953 UCS-3430 UCS-3432 EG-3404 MKW-2120 EG-3405Y 600-7326 220-5793-2-A001 220-5793-2-A002 540-0006-01 USS-3418 000-T00408-0C CLY LOCK W/KEYS FL FO32/841/XP/ECO SYLVANIA FL FO25/841/XP/ECO SYLVANIA CORD CLAMP SR10 PLASTIC TIE BELT 100 M/M NYLON CLAMP NK04 M SCR PH W/FS M4x8 M SCR TH CRM M4x8 TMP PRF SCR TH CRM M4x8 TMP PRF SCR TH CRM M4x12 M SCR PH W/S M4x25 FLG NUT M4 FLT WSHR CRM 4. 4-16x1. 6 FLT WSHR CRM 5. 5-20x1. 6 M SCR PH CRM M4x6 M SCR PH CRM M4x10 M SCR PH W/FS M4x10 HEX SKT H CAP SCR BLK 0Z M4x10 FLT WSHR M4 SPR WSHR M4 SPR WSHR CRM M4 FLG NUT M6 CRG BLT CRM M6x20 TMP PRF SCR TH CRM M4x16 WH BILLVALIDATOR WH EARTH BILL CARTON BOX 70 OWNERS MANUAL UCU ENG ARM S ARM L SHOVEL W60 SHOVEL W40 SHOVEL W30 AC CABLE CONNECT TYPE USA 15A KEY MASTER A001 KEY MASTER A002 WRENCH M4 TMP SCR SLIDE SPRING M SCR TH CRM M4x8 ASSY CABINET ASSY GLASS DOOR L ASSY GLASS DOOR R ASSY BACK LID ASSY CTRL PNL PLATE ASSY X MECHA 1P ASSY X MECHA 2P ASSY Y MECHA ASSY Z MECHA ASSY PIPE ASSY UFO MECHA ASSY MAIN BD SIDE GLASS SIDE GLASS SASH A SIDE GLASS SASH B L SIDE GLASS SASH B R SHIPPING BRKT TOP SHIPPING CENTER BAR SHIPPING BRKT MECHA GLASS EDGE GUARD A GLASS EDGE GUARD B FL COVER PLATE SW COVER L SW COVER R BILLBOARD FRONT BILLBOARD LEFT BILLBOARD RIGHT BILLBOARD WASHER BILL VALIDATOR DOOR BILL DOOR CUSSION BLIND PLATE LKG TNG BACK BD UPPER BRKT STICKER CAUTION FORK STICKER INSTR SUNLIGHT ENG STICKER CAUTION GLASS ENG STICKER 120V STICKER W POWER OFF ENG STICKER W DO NOT OPEN ENG STICKER W HIGH TEMP WIDE ENG STICKER BILL VALIDATOR STICKER LEFT STICKER RIGHT STICKER FRONT A STICKER FRONT B STICKER FRONT C PACKING SET UCU-0000 STICKER FCC STICKER C PRIZEDOOR ENG BACK BOARD B STICKER BACK BOARD 77 PARTS LIST 22 PARTS LIST 22 78 (2) ASSY CABINET (UCU-1000) (Including opposite side) (Earth terminal) When assembling (13), be sure to insert (105). [The (105) disk plate should be above (13)] Have the granulated surface face upward. Arrange the position of the convex part to the C beveling side. 4 pieces Detailed drawings for installation of (13) and (105). (NOT TO SCALE) (D-1/2) (D-2/2) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 101 102 103 104 105 106 PART NO. UCU-1001 UCS-1050X UCU-1060 UCU-1070 UCU-1080 USS-1200 UCU-1300 UCU-1310 UCU-1320 UCU-1340 839-1276R UCU-1003 UCU-1004 UCU-1005 DP-1148X UCU-1006 UCU-1007 UCU-1008 UCU-1009 UCU-1010 UCU-1011 UCU-1012 UCU-1013 UCU-1014 UCU-1015 UCU-1016 UCU-1017 UCU-1018 UCU-1019 UCU-1020 UCU-1021 UCU-1022 253-5366 421-12106-01 220-5794 560-5530-V 601-11480-8 601-11480-20 509-6121-01 280-6581-29 DESCRIPTION ASSY SUB CABINET ASSY SPEAKER ASSY SERVICE DOOR SW UNIT AC UNIT ASSY PRIZE SENSOR ASSY FL BASE L ASSY FL BASE R SIDE FL UNIT FLAP UNIT CREDIT BD US CTRL PNL COVER LEVER BRKT CASH BOX DOOR LKG TNG FIELD PLATE L FIELD PLATE R CHUTE ADJUST PLATE L CHUTE ADJUST PLATE R PARTITION HOLDER L PARTITION HOLDER R CORNER PARTITION L CORNER PARTITION R FIX PARTITION PARTITION BRKT CL PARTITION CL PARTITION FRONT PARTITION BRKT FRONT SPEAKER COVER WIRE COVER PRIZE SENSOR COVER L PRIZE SENSOR COVER R CASH BOX STICKER BULB 3. 8W14V UL CLY LOCK W/KEYS XFMR100-120V100V2A24V5A WB UL PLAPOINT L=8 PLAPOINT L=20 JOYSTICK 8WAY 50-6070-10(HAPP) BUSHING NB-29 NOTE PARTS LIST 201 202 203 204 205 206 207 208 301 000-P00308-W 000-P00408-W 000-T00408-0C 000-T00416-0C 008-T00408-0C 050-F00400 050-F00500 068-441616-0C UCU-60013 M SCR PH W/FS M3x8 M SCR PH W/FS M4x8 M SCR TH CRM M4x8 M SCR TH CRM M4x16 TMP PRF SCR TH CRM M4x8 FLG NUT M4 FLG NUT M5 FLT WSHR CRM 4. 4-16x1. 6 WH JOY STICK 22 79 (D-1/2) Details of part "I" (S=1/2) PARTS LIST Details for (25) installation position. 22 80 (3) ASSY SUB CABINET (UCU-1001) Details of part "F" (S=1/1) Details of part "E" (S=1/2) NOTE: (26) is to be affixed in alignment with the rectangular holes as shown in each figure. [. . . ]