User manual SEIKO 5R67

[. . . ] 5R66, 5R67 INSTRUCTIONS BEDIENUNGSANLEITUNG INSTRUCTIONS ISTRUZIONI INSTRUCCIONES INSTRUÇÕES (P. 3) (S. 157) (187 ) English You are now the proud owner of a Spring Drive Watch. For the best results, please read the instructions in this booklet carefully before using your Spring Drive Watch. Please keep this manual handy for ready reference. [. . . ] Set the 24-hour hand to indicate "5" on the 24-hour scale (the 2. 5 o'clock position), while the minute hand is pointing at the "0" minute position. Push the crown back in simultaneously with the time * The time difference adjustment * The setting of the 24-hour, minute and second hands function serves only for a time in to the time in the "different time zone area" is now a "different time zone area" where the time difference from completed. Push the crown back in upon completion of time setting. Tips for more accurate time setting · Keep in mind the following points in order to set the time more accurately. Before setting the time, wind the mainspring sufficiently until the power reserve indicator shows the fully-wound state. When starting to use a watch after it stops, wind the mainspring sufficiently and wait approximately 30 seconds after the second hand starts to move, then pull the crown out to the second click. Do not stop the second hand movement for 30 minutes or longer while the crown is at the second click position. If the stoppage of the second hand movement exceeds 30 minutes, push the crown back in to restart the second hand, wait at least 30 seconds, and then carry out the time setting once again. signal. 12 13 How to set the date · This watch is designed so that the date changes one day by turning the hour hand two full rotations in the same way as "the time difference adjustment function". · The date advances one day by turning the hour hand two full rotations clockwise, while the date is set back one day by turning the hour hand two full rotations counterclockwise. · After setting the time, it is necessary to set the date. Manual date adjustment is required on the first day after a month that has less than 31 days. Each time the hour hand makes two full rotations by turning the crown, the date is adjusted one day. Clockwise: the hour hand turns counterclockwise. After completing the time difference adjustment, check the position of the hour hand once again and push the crown back in. * * English Time difference table * Refer to the table below for time differences from GMT (UTC) in major cities in the world. Major cities in respective time zones Midway Islands Honolulu Anchorage Los Angeles , San Francisco Denver , Edmonton Chicago , Mexico City New York , Washington , Montreal Caracas, Santiago Rio de Janeiro Azores London , Casablanca Time difference with GMT (UTC) -11 hours -10 hours -9 hours -8 hours -7 hours -6 hours -5 hours -4 hours -3 hours -1 hour 0 hour English 16 17 English Paris , Rome, Amsterdam Cairo , Athens, Istanbul Moscow , Mecca, Nairobi Dubai Karachi, Tashkent Dacca Bangkok, Jakarta Hong Kong, Manila, Beijing, Singapore Tokyo, Seoul, Pyongyang Sydney , Guam, Khabarovsk Nouméa, Solomon Islands Wellington , Fiji islands, Auckland * * +1 hour +2 hours +3 hours +4 hours +5 hours +6 hours +7 hours +8 hours +9 hours +10 hours +11 hours +12 hours How to set the time and moon phase (for Cal. 5R67) English How to set the time · When setting the time, ensure that the watch is working: the main spring is sufficiently wound. Pull out the crown to the second click when the second hand is at the 12 o'clock (0 second) position. The second hand will stop on the spot. 2. Turn the crown counterclockwise (the 6 o'clock direction) to set the minute hand slightly behind the time you wish to set, and then slowly advance it to the desired time. 18 Cities marked with "" use daylight saving time. The time differences and use of daylight saving time in each city are subject to change according to the governments of the respective countries or regions. 3. Push the crown back in simultaneously with a time signal. The second hand will start to move immediately. 19 English Tips for more accurate time setting · Keep in mind the following points in order to set the time more accurately. Before setting the time, wind the mainspring sufficiently until the power reserve indicator shows the fully-wound state. When starting to use a watch after it stops, wind the mainspring sufficiently and wait approximately 30 seconds after the second hand starts to move, then pull the crown out to the second click. [. . . ] The watch has been adjusted so that it works accurately when it is worn on your wrist under a normal temperature range between 5 ºC and 35 ºC. Even though you wear the watch every day, the power reserve indicator does not move up. The watch temporarily gains or loses time. Correct this condition by moving and keeping the watch away from the magnetic source. If this action does not correct the condition, contact the retailer from whom the watch was purchased. If the watch does not return to its normal accuracy after resetting the time, contact the retailer from whom the watch was purchased. [. . . ]