User manual SEIKO 7T92

[. . . ] Conservare poi il manuale stesso per ogni qualsiasi eventuale futuro riferimento. Enhorabuena por su adquisición de un reloj SEIKO analógico de cuarzo Cal. Para óptimo resultado, lea detenidamente las instrucciones de este folleto antes de usar el reloj. Guarde este manual para consulta posterior. [. . . ] When the stopwatch is or has been measuring or is stopped, if the crown is pulled out to the second click, it will automatically reset the STOPWATCH hands to "0". If is recommended that the hands be set to the time a few minutes ahead of the current time, taking into consideration the time required to adjust the STOPWATCH hand position if necessary. When setting the hour hand, be sure to check that AM/PM is correctly set. The watch is so designed that the date changes once in 24 hours. When setting the minute hand, first advance it 4 to 5 minutes ahead of the desired time and then turn it back to the exact minute. 2. STOPWATCH HAND POSITION ADJUSTMENT If the STOPWATCH hands are not in the "0" position, follow the procedure below to set them to the "0" position. STOPWATCH 1/20-second hand A STOPWATCH second hand 6 STOPWATCH hour hand B STOPWATCH minute hand 6 A w w Press for 2 seconds to select STOPWATCH hand(s) to be adjusted. English q Selection of the hand(s) can be made in the following order by pressing button STOPWATCH 1/20-second hand A for 2 seconds. STOPWATCH second hand STOPWATCH hour and minute hands * The selected hand(s) turn(s) a full circule. B Press repeatedly to set the selected STOPWATCH hand(s) to the "0" position. * The hand(s) move(s) quickly if button B is kept pressed. * After all the adjustments are completed, check that the hour and minute hands for time display indicate the current time. w CROWN Push back into normal position in accordance with a time signal. 7 SETTING THE DATE English q Before setting the date, be sure to set the main time. CROWN 6 Pull out to first click. w Turn clockwise until the desired date appears. w Push back in to normal position. Date 1. It is necessary to adjust the date at the end of February and 30-day months. Otherwise, the date may not change properly. 8 STOPWATCH q The stopwatch can measure up to 12 hours in 1/20-second increments. q When the measurement reaches 12 hours, the stopwatch automatically stops counting. English STOPWATCH 1-20-second hand A STOPWATCH second hand STOPWATCH hour hand STOPWATCH second hand B [ Ex. : 2 hours, 30 minutes and 10. 85 seconds ] Movement of STOPWATCH 1/20-second hand q After the stopwatch is started, STOPWATCH 1/20-second hand moves for about 10 minutes and automatically stops at the "0" position. q When the measurement is stopped or split time is measured, it moves to indicate the elapsed 1/20 seconds. 9 English q After the stopwatch is restarted or split time is released, STOPWATCH 1/20-second hand moves for about 10 minutes and stops automatically. q In the same manner, if the stopwatch is stopped and restarted repeatedly or split time is measured and released repeatedly, STOPWATCH 1/20-second hand moves for about 10 minutes and stops automatically. Before using the stopwatch, be sure to check that the crown is set at the normal position and that the STOPWATCH hands are reset to the "0" position. * If the STOPWATCH hands do not return to the "0" position when the stopwatch is reset to "0", follow the procedure in "SETTING THE TIME AND ADJUSTING THE STOPWATCH HAND POSITION". Standard measurement A START A STOP B RESET w Accumulated elapsed time measurement A START 10 A STOP w A A STOP B RESET w w w RESTART * Restart and stop of the stopwatch can be repeated by pressing button A. w Split time measurement English A START B SPLIT B A STOP B RESET w w w SPLIT RELEASE * Measurement and release of split time can be repeated by pressing button B. Measurement of two competitors A START B FINISH TIME OF 1ST COMPETITOR A 2ND COMPETITOR FINISHES B FINISH TIME OF 2ND COMPETITOR w B RESET w w w w 11 English TACHYMETER (for models with tachymeter scale on the dial) To measure the hourly average speed of a vehicle 1 Use the stopwatch to determine how many seconds it takes to go 1 km or 1 mile. Tachymeter scale indicated by STOPWATCH second hand gives the average speed per hour. Ex. 1 STOPWATCH second hand: 40 seconds 2 Tachymeter scale: "90" "90" (tachymeter scale figure) x 1 (km or mile) = 90 km/h or mph q Tachymeter scale can be used only when the time required is less than 60 seconds. Ex. 2: If the measuring distance is extended to 2 km or miles or shortened to 0. 5 km or miles and STOPWATCH second hand indicates "90" on tachymeter scale: "90" (tachymeter scale figure) x 2 (km or mile) = 180 km/h or mph "90" (tachymeter scale figure) x 0. 5 (km or mile) = 45 km/h or mph 12 To measure the hourly rate of operation 1 English Use the stopwatch to measure the time required to complete 1 job. Tachymeter scale indicated by STOPWATCH second hand gives the average number of jobs accomplished per hour. Ex. 1 STOPWATCH second hand: 20 seconds 2 Tachymeter scale: "180" "180" (tachymeter scale figure) x 1 job = 180 jobs/hour Ex. [. . . ] Cycles per second) Loss/gain (monthly rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 15 seconds at normal temperature range (5° C ~ 35° C) (41° F ~ 95° F) Operational temperature range . . . . . . . . . . . . . . . . . ­10° C ~ +60° C (14° F ~ 140° F) Driving system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step motor, 4 pieces Display system Time/calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]