User manual SENNHEISER DW OFFICE

[. . . ] DECT Headset System Instruction manual DW Office Contents Contents Important safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The DW Office wireless headset system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Delivery includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The CHARGE STATUS LED ´ indicates the remaining battery charge of the headset. When the battery is about to run flat . . . only the LED segment 1 lights up weakly or flashes (see page 9). you hear a low battery warning (three beeps)in the headset. you have several minutes of battery reserve. When the battery is flat, the headset switches off. If the headset is outside the range of the base station, it will switch off after 30 minutes in order to conserve battery power. 22 Using the headset system Switching the headset on/off If you place the headset into the base station, the headset automatically switches to standby mode. In standby mode, the power consumption is very low and the radiated power is reduced to a minimum. The HEADSET LED lights up blue and the rechargeable battery is being charged. Switching the headset on Press and hold the LINK button for 5 seconds. The HEADSET LED flashes blue 3 times and the wireless link to the base station is established (where required). An ascending confirmation beep is heard in the headset. 4 3 Switching the headset off Press and hold the LINK button for 5 seconds. The HEADSET LED flashes red 3 times. Establishing a wireless link between headset and base station To establish a wireless link between headset and base station: Press the LINK button on the headset. The LINK LED ¿ lights up blue and the HEADSET LED flashes blue. To disconnect a wireless link between headset and base station: Press the LINK button on the headset. The LINK LED ¿ and the HEADSET LED off. go 4 ³ 3 » You can also establish or disconnect the wireless link by pressing the PC button ³ or the PHONE button » on the base station (depending on the selected mode (PC or Phone), see page 28). If your telephone has a built-in electronic hook switch supporting the MSH standard (see page 13), you can only disconnect the wireless link between headset and base station by placing the headset into the base station. The control signals ("accept a call", "end a call") of the headset are still transmitted to the electronic hook switch without. ¿ 23 Using the headset system Putting the headset on and adjusting it Wearing the headset with the earhook Slightly pull the earhook away from the headset. Place the earhook behind your ear so that it follows the contour of your ear. Adjust the headset so that a comfortable and secure fit is ensured. 6 Wearing the headset with the headband Adjust the headband to your head. Put on the headset so that the ear pad rests comfortably on your ear and that the headband runs over the top of your head. Orient the microphone towards your mouth. B D Calling via the fixed line phone using the headset Accepting an incoming call You hear the ring tone of the fixed line phone: Put on the headset and establish a wireless link between headset and base station (see page 23). 24 Using the headset system If a handset lifter/electronic hook switch is used, the call is automatically accepted. If you receive a call and a handset lifter/electronic hook switch with ring tone detection is used, you hear a ring tone in the headset and the LED of the PHONE button » flashes white. If no handset lifter/electronic hook switch is used: Accept the call by lifting the handset or by pressing the "accept call" button on your fixed line phone. Making a call If a handset lifter/electronic hook switch is used: Dial the desired number. [. . . ] 75 g DECT EU version: CAT IQ 1. 0 Transmission frequency SAR value 1, 880 to 1, 900 MHz 0. 196 W/kg (max. 10 g SAR) US version: DECT 6. 0 1, 920 to 1, 930 MHz 0. 093 W/kg (max. 1 g SAR) 38 Manufacturer Declarations Manufacturer Declarations Warranty Sennheiser Communications A/S gives a warranty of 24 months on this product. For the current warranty conditions, please visit our web site at www. sennheiser. com or contact your Sennheiser partner. [. . . ]