User manual SENNHEISER EW 300 IEM G2

[. . . ] W 300 IEM SR 350 IEM Instructions for use Contents Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The ew 300 IEM G2 systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The channel bank system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Delivery includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Both the accupack and the charger are available as accessories. The accupack is fitted with an integrated sensor which is ­ via a third contact ­ monitored by the electronics of the receiver and the charger. The sensor is necessary for the following control purposes: The taking into account of the different voltage characteristics of primary cells (batteries) and accupacks. The battery status indications on the displays, the transmission of transmitter battery status information to the rack-mount receivers and the switch-off thresholds at the end of the operating time are corrected correspondingly. Due to the missing sensor, individual rechargeable battery cells will not be identified as accupacks. The monitoring of the accupack temperature during charging in the L 2015 charger. The prevention of improper charging of inserted primary cells (batteries). Due to the missing sensor, individual rechargeable battery cells will also not be charged in the L 2015 charger. 17 Connecting the headphones CAUTION!Listening at high volume levels for long periods can lead to permanent hearing defects. Set the volume for the connected headphones to the minimum before putting the headphones on. For monitoring purposes, connect the supplied earphones or any Sennheiser stereo headphones with 3. 5 mm stereo jack plug to the headphone output (PHONES) ³. First, set the volume control · to the lowest volume by turning it to the left as far as possible. Then gradually turn up the volume. ³ · Using the components Switching the components on/off Switching the transmitter on/off Press the ON button ¶ to switch the transmitter on. To switch the transmitter off, press the ON button until "OFF" appears on the display. Note: The transmitter can only be switched off when the standard display is shown on the display panel. Within the operating menu, the ON button serves as the ESC (cancel) key, i. e. you cancel your entry and return to the standard display. After switch-off, the transmitter is in standby mode. To disconnect the transmitter from the mains, pull out the mains connector from the wall socket!Switching the receiver on/off To switch the receiver on, turn the volume control clicks. To switch the receiver off, turn the volume control until it clicks. clockwise until it counterclockwise ¶ » Note: The receiver has a short switch-on delay. [. . . ] An up-to-date list of all service partners of Sennheiser electronic GmbH & Co. KG worldwide are available on the internet at www. sennheiser. com. The customer bears the risk of shipment. To avoid any damage in transit, please use the original packaging if possible. 41 CE Declaration of Conformity This equipment is in compliance with the essential requirements and other relevant provisions of Directives 1999/5/EC, 2004/108/EU or 2006/95/EC. [. . . ]