User manual SENNHEISER HDE 2020-D

[. . . ] System 2020 Tourguide Instruction manual Contents Contents Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Overview of the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 The operating controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] you can turn it endlessly to the left or right. 31 Using the components Charging the rechargeable batteries CAUTION!· Only use the charging case for charging the SK 2020 D bodypack transmitter, the HDE 2020 D and EK 2020 D receivers and the BA 2015 accupack. · Never try to charge other rechargeable batteries or non-rechargeable batteries!Charging the accupack in the bodypack transmitter To charge the bodypack transmitter in the EZL 202020 L charging case: Place the transmitter with the accupack inserted into the charging compartment for accupack/bodypack transmitter ³ as shown in the diagram on the left. When placed into a charging compartment, the bodypack transmitter automatically switches off. The red LED CHARGE/ERROR · of the charging compartment lights up. · » After the accupack has been fully charged, the green LED READY » lights up. Notes: · Charging a completely discharged accupack takes approx. · Alternatively, you can remove the accupack from the bodypack transmitter and insert it into the charging compartment for accupack/bodypack transmitter ³ as described in the following section. · The charging case has no error indication like the one on the L 2015 charger ("red flashing LED"). 32 Using the components Charging the BA 2015 accupack ³ To charge the accupack of the radio microphone or bodypack transmitter: Remove the accupack as described on page 26 or page 27. Place the accupack into the charging compartment for accupack/bodypack transmitter ³ as shown in the diagram on the left. The red LED CHARGE/ERROR · of the charging compartment lights up. · » After the accupack has been fully charged, the green LED READY » lights up. Notes: · Charging a completely discharged accupack takes approx. It is normal for the accupacks to get hot during charging. · However, the charging process may take longer if: · the accupack is deep-discharged and first has to be reconditioned by a deep discharge recovery charge, · the ambient temperature is close to or over 40°C, since, in order to protect the accupack, the charging process will be interrupted until the temperature has dropped to a safe level. · For safety reasons, each charging process will be interrupted after 4 hours. · When not using the BA 2015 accupack for extended periods of time, charge it about every three to six months. 33 Using the components Charging the receivers' built-in rechargeable batteries Place the receiver into one of the charging compartments for receivers ´/µ (light blue in the diagram). · The LED · of the HDE 2020 D or · the LED ¿ of the EK 2020 D lights up (see table). LED colour Meaning red The built-in rechargeable battery is being charged. The built-in rechargeable battery is fully charged. The temperature of the built-in rechargeable battery is over 40°C or below 3°C. The built-in rechargeable battery is defective. Interrupt the charging process and contact your Sennheiser Service. ¿ · ´ green µ red (flashing) yellow/ orange Notes: · Charging a completely discharged rechargeable battery of the HDE 2020 D takes approx. [. . . ] Statements regarding FCC and Industry Canada This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]