User manual SENNHEISER SI 30-1500 SINGLE PRODUCT SHEET

[. . . ] MONO Jack) 4. 707" Power Supply SI 30 transmitter andPin Texas30 emitter are the primary components of the system. SZI Socket) (119. 56 mm) (2 These are powered by the NT20-4-120 AC power adapter and KKY20-015 octopus 1. 000" (25. 40 mm) power cable, which connects up to four SI30 and SZI30. For easy installation, the RF Output SI30 and SZI30 may mm MONO Jack)or ceiling mounted with the IZK20 mounting clamp (3. 5 be wall Internal IR Transmission Diodes and IZM20 mounting hardware, in combination with the WM1 wall/ceiling mount. 3/8"Side Thread Far AF Input The RI250 stethophoneJack) LED Indicator for Transmission Mode receiver includes the BA151 single-channel infrared (3. 5 mm MONO 4. 707" . 574" ø. 584" rechargeable battery, which conveniently rechargesmm)mm) the L151-10/NT with (119. 56 (14. 58 (14. 83 mm) charging unit with power supply. 1. 000" (25. 40 mm) RF Output (3. 5 mm MONO Jack) General Description AF Input (3 Pin Texas Socket) IR Transmission Diodes LED Indicator for Transmission Mode SZI30 1. 333" 3/8" Internal Thread (33. 86 mm) 1. 347" (34. 21 mm) IR Transmission Diodes LED Indicator for Transmission Mode ø. 740" (18. 80 mm) 3. 364" (85. 45 mm) 5/8" Internal Thread IZK20 . 574" (14. 58 mm) 34. 21" (79. 25 mm) 3/8" Thread 4. 350" (7110. 49 mm) ø. 584" (14. 83 mm) 3/8" Internal Thread ø. 640" (16. 26 mm) . 978" (24. 84 mm) 1. 194" (30. 33 mm) SI30 1. 347" (34. 21 mm) ø. 740" (18. 80 mm) 3 Pin Texas Connector 1/8" Stereo Jack Plug Ratchet Adjustment 1/8" to 1/4" For Angle Stereo Jack Adapter 5. 433" (138. 00 mm) 5. 286" (134. 26 mm) ø. 640" (16. 26 mm) ø. 752 (19. 10 mm) 3/8" 5/8" External Replaceable Thread ear Thread Internal Thread cushions 5/8" ø. 640" (16. 26 mm) IZM20 2 CH-AF(116. 10 mm) Connection Cable 3/8" Thread 4. 350" (7110. 49 mm) ø1. 936 (49. 17 mm) 4. 571" 34. 21" (79. 25 mm) ø. 640" 3/8" (16. 26 mm) Thread Power Supply (2 Pin Texas Socket) RF Output (3. 5 mm MONO Jack) Channel Switch Stereo, CH 1, CH 2 3. 406" (86. 51 mm) Adjusting Knob ø. 640" Receiving Diodes (16. 26(behind plastic cover) mm) 3/8" Thread Two IR 7. 390" (187. 71 mm) 2. 724" (69. 19 mm) 5. 433" (138. 00 mm) ø. 161 (4. 09 mm) ø. 743 Thread (44. 27 mm) Mounting Plate ø. 1242 4. 707" mm) (31. 55 (119. 56 mm) 3/8" ø. 640" (16. 26 mm) ON/OFF Volume Control 1. 467" (37. 26 mm) Inserted BA151 Rechargeable Battery WM1 RI250 LED Indicator Trickle Charge (Green) Button: Press to begin 10 HR charge cycle LED Indicator Charge (Red) Charging for RI250, HDI302 Infrared Receivers (Up to ten) 1. 000" (25. 40 mm) AF Input (3 Pin Texas Socket) IR Transmission Diodes LED Indicator for Transmission Mode L151­10NT 1. 500" (38. 10 mm) SI30­Two channel switchable or stereo infrared transmitter. [. . . ] The maximum coverage area shall be approx. The operating voltage shall be 24-27 DC via 2-pin Texas socket. The current consumption shall be approx. 4. 64" x 0. 98" x 3. 54" and weigh approx. The SZI30 shall be an infrared emitter with a carrier frequency band that extends to 6 MHz RF input and RF output via 3. 5 mm mono socket. The unit shall offer excellent reliability due to 10 independent diodes. The unit shall offer a 24-27 V DC via 2-pin Texas socket. The power supply NT20-4-120 shall provide power for up to four SI30/SZI30, and shall have an output voltage of approx. The power distribution cable KKY20-015 shall connect up to four SI30/SZI30 to an NT20-4-120 power supply, and shall have an approx. length of 0. 15 m, with four Texas plugs and one Texas socket. The RF connection cable KR20-015 shall provide connection, via two 3. 5mm jack plugs, of an SI30 to an SZI30 or for daisy-chaining two SZI30's, with a length of 0. 15 m. The SI30 and SZI30 shall be wall or ceiling mountable via the IZK20 mounting clamp with 3/8" internal thread. The IZM20 mounting kit shall contain a 3/8" and 5/8" internal thread for mounting two to four SI30 and SZI30. Every modulator/radiator must utilize one IZK20 mounting clamp. The WM1 shall provide wall or ceiling mounting via a mounting clamp with 5/8" external male thread, with a mounting plate diameter of 1 5/8". The single-channel infrared receivers shall be stethoset design with a carrier frequency of 2. 3 MHz. [. . . ] The Sennheiser Service Department will be the sole authority to determine the validity of all warranty issues. This Limited Product Warranty is Sennheiser Electronic Corporation's only warranty, and the customer's only remedy concerning Sennheiser products. All other representations and warranties, express or implied, written or oral, including, but not limited to, any warranties of merchantability, fitness for a particular purpose, or non-infringement, are expressly excluded. [. . . ]