User manual SENNHEISER SIS 1019 A 20

[. . . ] 7 Available system components ­ scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overview of the components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 WiCOS wireless conference units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WiCOS AP access point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In the address box of the browser, type the IP address of the access point: the factory default IP address 192. 168. 0. 10 or your adapted IP address. Press the Enter key or click the "Refresh" button of your web browser. The web server appears in the browser window and prompts for a password. If you have not assigned a password: Type the default password "123" into the entry field. The "Summary" overview screen of the web server appears. If you have assigned a password (see page 52): Type the password into the entry field. The "Summary" overview screen of the web server appears. If you have forgotten the password, you can reset the access point to the factory default settings in order to be able to access the web server (see page 44). Attention: If the access point is reset, any custom settings will be lost! 48 Configuring the conference system Adjusting the basic settings ­ "Setup" Overview screen ­ "Summary" The overview screen provides information on the system settings ("System Information") and the device settings ("Device Information"), e. g. In the main navigation, click "Setup". The "Summary" overview screen appears. Setting "System Name" "IP Address" "Subnet Mask" "Address Mode" "Base MAC Address" "Serial Number" "Model Name" "Hardware Version" "Boot Version" "Firmware Version" "FPGA Version" "RF Hardware 1 Version" "RF Hardware 2 Version" "RF Firmware 1 Version" "RF Firmware 2 Version" Function/Meaning User selectable name for the network address of the conference system IP address of the access point Subnet address of the address point Address mode of the network address MAC address of the access point Serial number of the access point Model name of the access point Version number of the hardware Version number of the boot firmware Version number of the firmware Version number of the conference units' firmware Version number of the transmission hardware Version number of the reception hardware Version number of the transmission firmware Version number of the reception firmware Additional information see page 49 see page 67 Setting the network address of the access point ­ "TCP/IP Settings" The fixed IP address 192. 168. 0. 10 and the subnet address 255. 255. 255. 0 are factory preset. Using this address, you can access the web server. 49 Configuring the conference system There are two ways to integrate the access point into the network and to use the web server. From the "Country selection" drop-down list, select the correct country is which the conference system is to be used. In the main navigation, click "Setup" > "Country selection". The "Country selection" overview screen appears. From the "Country selection" drop-down list, select the country in which the conference system is to be used. 51 Configuring the conference system Click "Save settings". The selected country is displayed in the "Selected Country Region" field. The conference system will only use frequencies and transmission powers that are approved and legal in the selected country/region. The country-specific radio settings for the United States and Canada, "US/Canada", are the most restricted radio settings in the conference system. These settings are used as the factory default settings. Setting the password protection ­ "Admin" You can protect the access point against unauthorized access and changes to the system by setting a password. The factory default password is "123". In the main navigation, click "Setup" > "Admin". The "Admin: authentication" overview screen appears. In the "Old password" field, type the old password. [. . . ] 830 g RAL 9011 WiCOS BA Lithium-Ion battery pack Nominal output voltage Capacity Charging voltage Charging current Charging time Operating temperature Dimensions Weight Color 7. 2 V 6600 mAh 15 V . . . 380 g RAL 9011 WiCOS MIC gooseneck microphone Pick-up pattern Frequency response Sensitivity (1 kHz) Max. SPL (1 kHz) Temperature range cardioid 50 - 20, 000 Hz 8 mV / Pa +/­ 2. 5 dB 133 dB 0 °C to + 45 °C 84 Specifications Microphone gooseneck length Weight Color approx. 70 g matt black Certifications (WiCOS AP, WiCOS D, C, DV, CV, WiCOS BA) In compliance with Europe: EMC Radio EN 301489-1/-17 EN 300328 EN 301893 EN 300440-1/-2 EN 60065 EN 62311 (SAR) Safety USA (WiCOS BA only): Meets the requirements of the UL 1642 safety standard. [. . . ]